Brocade Fabric OS Encryption Administrator’s Guide Support Manual do Utilizador Página 286
- Página / 332
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
266 Fabric OS Encryption Administrator’s Guide (DPM)
53-1002922-01
Key vault diagnostics
6
Use the --sync -securitydb command to distribute the security database from the group leader
node to all member nodes. This command is valid only on the group leader.
In scenarios where this master key propagation issue still persists, exporting the master key to a
file and recovering it resolves the issue. To do this, use the following commands:
• Use the cryptocfg --exportmasterkey -file option to export the master key to a file.
• Use the cryptocfg --recovermasterkey currentMK -srcfile to recover the master key.
Aborting a pending database transaction
You can abort a pending database transaction for any device configurations invoked earlier
through the CLI or BNA interfaces by completing the following steps.
1. Use the
--transshow command to determine the currently pending transaction ID.
The
--transshow command displays the pending database transaction for any device
configurations invoked earlier through the CLI or BNA interfaces. The command displays the
transaction status (completed or pending), the transaction ID, and the transaction owner (CLI
or BNA).
2. Use the
--transabort <transaction_ID> command to abort the transaction, where
<transaction_ID> specifies the ID of the transaction to be aborted.
Key vault diagnostics
With the introduction of Fabric OS 7.0.0, you can run key vault diagnostics tests to identify any key
vault connectivity or key operation errors. You configure the key vault diagnostic test using the
cryptocfg
--kvdiag command.
If an encryption switch is part of an EG, the diagnostic testing is performed on that switch only and
not the entire group. If multiple nodes in an encryption group have different Fabric OS versions,
only those nodes running Fabric OS 7.0.0 and later can be configured for periodic key vault
diagnostic testing.
You can set the diagnostic tests to run at regular intervals. When incidents occur, the findings are
collected in log reports. The first instance of a failure and subsequent restoration of operation is
reported as a Remote Access Server (RAS) log. Subsequent findings for the same incident are not
logged to avoid redundant messages.
Key vault connectivity
Key vault connectivity is adiagnostics feature that allows you to periodically collect information
about the state of key vault connectivity from the Brocade Encryption Switch and possible version,
configuration, or cluster information of the key vault (KV).
This feature reports the following types of configuration information:
• Key Vault/Cluster scope:
• CA Certificate and its validity (for example, valid header and expiry date)
• Key Vault IP/Port
• KV firmware version
• Time of day on the KV
- Fabric OS Encryption 1
- Document History 2
- Document Title iii 3
- 53-1002720-02 3
- Contents 5
- 53-1002922-01 10
- About This Document 15
- What’s new in this document 16
- Document conventions 16
- Command syntax conventions 17
- Notes, cautions, and warnings 17
- Additional information 18
- Getting technical help 19
- Document feedback 20
- Encryption Overview 21
- Terminology 22
- The Brocade Encryption Switch 24
- The FS8-18 blade 25
- FIPS mode 25
- Performance licensing 25
- Usage limitations 26
- FIGURE 2 Encryption overview 27
- FIGURE 3 Frame redirection 28
- IO Sync LAN 29
- FIGURE 5 DEK life cycle 30
- Master key management 31
- Support for virtual fabrics 31
- Encryption Center features 34
- Encryption user privileges 35
- Smart card usage 36
- Using system cards 41
- Deregistering system cards 43
- Using smart cards 43
- Tracking smart cards 44
- Editing smart cards 46
- Network connections 47
- Blade processor links 47
- (KAC) certificate 48
- Encryption preparation 55
- Creating an encryption group 55
- --initnode command 65
- --set -keyvault command 65
- --reg keyvault command 65
- Creating HA clusters 72
- Failback option 74
- Invoking failback 74
- Adding an encryption target 75
- FIGURE 46 Next Steps screen 83
- Configuring storage arrays 91
- Remote replication LUNs 91
- Moving targets 96
- Tape LUN statistics 99
- Encryption engine rebalancing 103
- Master keys 104
- Active master key 105
- Alternate master key 105
- Master key actions 106
- ATTENTION 107
- Creating a master key 113
- Security settings 114
- Setting zeroization 115
- Redirection zones 117
- Disk device decommissioning 117
- Decommissioning disk LUNs 118
- Displaying Universal IDs 120
- Setting disk LUN Re-key All 121
- Thin provisioned LUNs 125
- Thin Provisioning support 126
- General tab 133
- Members tab 135
- Members tab Remove button 136
- Security tab 137
- HA Clusters tab 139
- Tape Pools tab 141
- Adding tape pools 142
- Engine Operations tab 143
- TABLE 3 Encryption acronyms 144
- In this chapter 145
- Overview 146
- Command validation checks 146
- (Continued) 148
- Cryptocfg Help command output 150
- Management LAN configuration 150
- Configuring cluster links 151
- Node is a group leader node 152
- Node is a member node 152
- • FIPS crypto officer 153
- • FIPS user 153
- • Node CP certificate 153
- Submitting the CSR to a CA 156
- • cryptocfg --initEE 163
- • cryptocfg --regEE 163
- • cryptocfg --enableEE 163
- High availability clusters 168
- Creating an HA cluster 169
- Policy Configuration Examples 172
- Re-exporting a master key 173
- Viewing the master key IDs 174
- Zoning considerations 177
- Frame redirection zoning 178
- Gathering information 182
- Crypto LUN configuration 186
- Discovering a LUN 187
- Configuring a Crypto LUN 187
- Configuring a tape LUN 191
- Decommissioning LUNs 195
- SRDF LUNs 199
- SRDF pairs 200
- Adding replication LUNs 201
- Reading metadata after sync 202
- -newLUN option 203
- TF snapshot rekeying details 208
- ID> <initiator PWWN> 209
- -not_ready option of TF 209
- <initiator PWWN> 209
- Tape pool configuration 213
- Tape pool labeling 214
- NetBackup labeling 215
- NetWorker labeling 215
- Creating a tape pool 216
- Deleting a tape pool 216
- Modifying a tape pool 217
- First-time encryption 222
- Data rekeying 225
- Resource allocation 226
- Rekeying modes 226
- Deployment Scenarios 231
- --rdcreate [host wwn] 240
- FIGURE 103 FCIP deployment 242
- Data mirroring deployment 243
- VMware ESX server deployments 245
- General guidelines 248
- Enabling a disabled LUN 253
- HP-UX considerations 253
- AIX considerations 253
- Disk metadata 254
- Tape metadata 254
- Tape data compression 255
- Tape pools 255
- Tape block zero handling 256
- Tape key expiry 256
- Avoid double encryption 258
- PID failover 258
- Manual rekey 259
- Latency in rekey operations 259
- Key vault best practices 263
- Tape device LUN mapping 263
- Deleting an encryption group 269
- Removing an HA cluster member 269
- Deleting an HA cluster member 273
- Failover/failback example 274
- Recovery 275
- -hbmisses and -hbtimeout 280
- Key vault diagnostics 286
- --perfshow 287
- -portperfshow 287
- Command Activity 291
- Problem Resolution 291
- General errors and conditions 292
- LUN policy troubleshooting 299
- MPIO and internal LUN states 301
- Multi-node EG replacement 302
- Single-node EG replacement 304
- Multi-node EG Case 305
- Single-node EG Replacement 308
- Deregistering a DPM key vault 310
- FIGURE 111 DPM Clients page 311
- TABLE 15 Compatibility Matrix 313
- Encryption group Nodes 314
- State and Status Information 317
- Security processor KEK status 318
- Encrypted LUN states 318
- TABLE 22 Tape LUN states 321
Manuais e produtos relacionados com Acessórios para Computador Brocade Fabric OS Encryption Administrator’s Guide Support
Acessórios para Computador Brocade Fabric OS Encryption Administrator’s Guide Support Manual do Utilizador
(324 páginas)
(324 páginas)
Acessórios para Computador Brocade Fabric OS Encryption Administrator’s Guide Support Manual do Utilizador
(322 páginas)
(322 páginas)
Acessórios para Computador Brocade Fabric OS Feature Support Matrix (Supporting Fabri Manual do Utilizador
(12 páginas)
(12 páginas)
Acessórios para Computador Brocade Fabric OS Command Reference (Supporting Fabric OS Manual do Utilizador
(127 páginas)
(127 páginas)
Acessórios para Computador Brocade Fabric OS Software Licensing Guide (Supporting Fab Manual do Utilizador
(58 páginas)
(58 páginas)
Acessórios para Computador Brocade Fabric OS Encryption Administrator’s Guide Support Manual do Utilizador
(300 páginas)
(300 páginas)
Acessórios para Computador Brocade Fabric OS Upgrade Guide (Supporting Fabric OS v7.3 Manual do Utilizador
(34 páginas)
(34 páginas)
Acessórios para Computador Brocade Fabric OS Troubleshooting and Diagnostics Guide (S Manual do Utilizador
(130 páginas)
(130 páginas)
Acessórios para Computador Brocade Fabric Watch Administrators Guide (Supporting Fabr Manual do Utilizador
(116 páginas)
(116 páginas)
Acessórios para Computador Brocade Flow Vision Administrators Guide (Supporting Fabri Manual do Utilizador
(90 páginas)
(90 páginas)
Acessórios para Computador Brocade Monitoring and Alerting Policy Suite Administrator Manual do Utilizador
(114 páginas)
(114 páginas)
Acessórios para Computador Brocade EZSwitchSetup Administrator’s Guide (Supporting 30 Manual do Utilizador
(64 páginas)
(64 páginas)
Acessórios para Computador Brocade FICON Administrator’s Guide (Supporting Fabric OS Manual do Utilizador
(126 páginas)
(126 páginas)
Pertronix JBA Exhaust 40-3014 manuels
Manuels d'utilisation et guides de l'utilisateur pour Pour la voiture Pertronix JBA Exhaust 40-3014.
Nous fournissons des manuels en pdf 1 Pertronix JBA Exhaust 40-3014 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Comentários a estes Manuais