Brocade Network OS Command Reference v4.1.0 Manual do Utilizador

53-1003115-0105 Feb 2014®Network OSCommand ReferenceSupporting Network OS v4.1.0

x Network OS Command Reference53-1003115-01dot1x reauthMax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .240dot1x test eapol-

62 Network OS Command Reference53-1003115-01cee-map (configuration)2cee-map (configuration) Enters the CEE map configuration mode.Synopsis cee-map def

962 Network OS Command Reference53-1003115-01show prom-access2show prom-accessShows the Boot PROM access status.Synopsis show prom-access Operands Non

Network OS Command Reference 96353-1003115-01show qos flowcontrol interface2show qos flowcontrol interface Displays all of the configured flow control

964 Network OS Command Reference53-1003115-01show qos flowcontrol interface25 Off Off Off Off 06 Off Off Off Off 0See Also show qos interface, s

Network OS Command Reference 96553-1003115-01show qos interface2show qos interface Displays a summary of all QoS configurations applied on an interfac

966 Network OS Command Reference53-1003115-01show qos interface2 CoS2 TX on, RX onMulticast Packet Expansion Rate Limit 3000000 pkt/s, max burst 4096

Network OS Command Reference 96753-1003115-01show qos maps2show qos mapsDisplays information on the defined QoS maps.Synopsis show qos maps [cos-mutat

968 Network OS Command Reference53-1003115-01show qos maps dscp-cos2showqosmapsdscp-cosDisplays configured DSCP-CoS maps.Synopsis show qos maps dscp-c

Network OS Command Reference 96953-1003115-01show qos maps dscp-mutation2showqosmapsdscp-mutationDisplays configured DSCP-mutation maps.Synopsis show

970 Network OS Command Reference53-1003115-01show qos maps dscp-traffic-class2showqosmapsdscp-traffic-classDisplays configured DSCP-Traffic-Class maps

Network OS Command Reference 97153-1003115-01show qos queue interface2show qos queue interfaceDisplays the runtime state retrieved from the interface

Network OS Command Reference 6353-1003115-01cee-map (FCoE)2cee-map (FCoE) Assigns a cee-map to the FCoE Fabric-Map. Synopsis cee-map default no cee-ma

972 Network OS Command Reference53-1003115-01show qos rcv-queue interface2show qos rcv-queue interface Displays a summary of the runtime ingress queue

Network OS Command Reference 97353-1003115-01show qos rcv-queue multicast2show qos rcv-queue multicast Displays the runtime state retrieved from the d

974 Network OS Command Reference53-1003115-01show qos red profiles2show qos red profilesDisplays configured Random Early Discard (RED) profiles.Synops

Network OS Command Reference 97553-1003115-01show qos red profiles2CoS-to-Traffic Class map 'default' In-CoS: 0 1 2 3 4 5 6 7 ------

976 Network OS Command Reference53-1003115-01show qos red statistics interface2show qos red statistics interface Displays Random Early Discard (RED) s

Network OS Command Reference 97753-1003115-01show rbridge-id2show rbridge-idDisplays the RBridge ID of each node that is configured in a Virtual Clust

978 Network OS Command Reference53-1003115-01show rbridge-running config2show rbridge-running config Displays configuration for an RBridge ID. Synopsi

Network OS Command Reference 97953-1003115-01show rbridge-running config2dpod 1/0/17!dpod 1/0/18!dpod 1/0/19!dpod 1/0/20!dpod 1/0/21!dpod 1/0/22!dpod

980 Network OS Command Reference53-1003115-01show rbridge-running config2 priority-group-table 1 weight 40 pfc on priority-group-table 15.0 pfc off pr

Network OS Command Reference 98153-1003115-01show rbridge-running config2 system-monitor fan threshold marginal-threshold 1 down-threshold 2 system-mo

64 Network OS Command Reference53-1003115-01certutil import ldapca2certutil import ldapcaImports an LDAP CA certificate.Synopsis certutil import ldapc

982 Network OS Command Reference53-1003115-01show rbridge-local-running-config2show rbridge-local-running-configDisplays local configuration for an RB

Network OS Command Reference 98353-1003115-01show rbridge-local-running-config2dpod 1/0/17!dpod 1/0/18!dpod 1/0/19!dpod 1/0/20!dpod 1/0/21!dpod 1/0/22

984 Network OS Command Reference53-1003115-01show rbridge-local-running-config2 fabric isl enable fabric trunk enable no shutdown!interface TenGigabit

Network OS Command Reference 98553-1003115-01show redundancy2show redundancyDisplays the control processor redundancy settings of the Management Modul

986 Network OS Command Reference53-1003115-01show rmon2show rmonDisplays the current RMON status on the switch.Synopsis show rmon [alarms [number] [br

Network OS Command Reference 98753-1003115-01show rmon2To display the RMON events:switch# show rmon events event Index = 4 Description "My Descri

988 Network OS Command Reference53-1003115-01show rmon history2show rmon historyDisplays information gathered by rmon event and rmon alarm commands.Sy

Network OS Command Reference 98953-1003115-01show route-map2show route-mapDisplays all interfaces in the system that currently have a route map applie

990 Network OS Command Reference53-1003115-01show route-map2Policy routing matches: 100 packets; 500000 bytesip policy route-map abc permit 20 (Active

Network OS Command Reference 99153-1003115-01show route-map interface2show route-map interfaceDisplays the status of a route-map application on the sp

Network OS Command Reference 6553-1003115-01certutil import ldapca2In VCS modeTo import a certificate for LDAP:switch# certutil import ldapca director

992 Network OS Command Reference53-1003115-01show route-map interface2set ip interface null0Policy routing matches: 0 packets; 0 bytessw0# show route-

Network OS Command Reference 99353-1003115-01show running reserved-vlan2show running reserved-vlanDisplays the range of reserved VLAN values.Synopsis

994 Network OS Command Reference53-1003115-01show running-config2show running-configDisplays the contents of the running configuration.Synopsis show r

Network OS Command Reference 99553-1003115-01show running-config aaa2show running-config aaaDisplays the AAA server configuration.Synopsis show runnin

996 Network OS Command Reference53-1003115-01show running-config aaa accounting2show running-config aaa accountingDisplays the AAA server accounting c

Network OS Command Reference 99753-1003115-01show running-config access-list2show running-config access-listDisplays currently configured ACLs in the

998 Network OS Command Reference53-1003115-01show running-config ag2show running-config agDisplays the configured N_Port to VF_Port mappings, port gro

Network OS Command Reference 99953-1003115-01show running-config ag2 modes lb rename pg0 !timeout fnm 120counter reliability 25!!sw0# show runnin

1000 Network OS Command Reference53-1003115-01show running-config banner2show running-config bannerDisplays the switch banner.Synopsis show running-co

Network OS Command Reference 100153-1003115-01show running-config cee-map2show running-config cee-mapDisplays the Converged Enhanced Ethernet (CEE) ma

66 Network OS Command Reference53-1003115-01certutil import sshkey2certutil import sshkeyImports the SSH public key for an SSH user from the remote ho

1002 Network OS Command Reference53-1003115-01show running-config class-map2show running-config class-mapDisplays configured class-maps.Synopsis show

Network OS Command Reference 100353-1003115-01show running-config diag post2show running-config diag postDisplays the defined POST configuration. Syno

1004 Network OS Command Reference53-1003115-01show running-config dot1x2show running-config dot1xDisplays the IEEE 802.1x Port Authentication configur

Network OS Command Reference 100553-1003115-01show running-config dpod2show running-config dpodDisplays Dynamic Ports on Demand (DPOD) license informa

1006 Network OS Command Reference53-1003115-01show running-config fabric route mcast2show running-config fabric route mcastDisplays fabric route multi

Network OS Command Reference 100753-1003115-01show running-config fcoe2show running-config fcoeDisplays the running configuration for FCoE. Synopsis s

1008 Network OS Command Reference53-1003115-01show running-config fcsp auth2show running-config fcsp authDisplays the E_Port-to-EX_Port authentication

Network OS Command Reference 100953-1003115-01show running-config hardware connector2show running-config hardware connectorDisplays the SFP configurat

1010 Network OS Command Reference53-1003115-01show running-config interface fcoe2show running-config interface fcoeDisplays the status of FCoE interfa

Network OS Command Reference 101153-1003115-01show running-config interface FibreChannel2show running-config interface FibreChannelDisplays Fibre Chan

Network OS Command Reference 6753-1003115-01certutil import sshkey2Password: ***********switch# 2012/11/14-10:28:58, [SEC-3050], 75,, INFO, VDX6720-60

1012 Network OS Command Reference53-1003115-01show running-config interface FibreChannel2Enter interface FibreChannel to set the values.Examples To di

Network OS Command Reference 101353-1003115-01show running-config interface fortygigabitethernet2show running-config interface fortygigabitethernetDis

1014 Network OS Command Reference53-1003115-01show running-config interface fortygigabitethernet bpdu-drop2show running-config interfacefortygigabite

Network OS Command Reference 101553-1003115-01show running-config interface fortygigabitethernet cee2show running-config interface fortygigabitetherne

1016 Network OS Command Reference53-1003115-01show running-config interface fortygigabitethernet channel-group2show running-config interfacefortygiga

Network OS Command Reference 101753-1003115-01show running-config interface fortygigabitethernet description2show running-config interfacefortygigabi

1018 Network OS Command Reference53-1003115-01show running-config interface fortygigabitethernet dot1x2show running-config interface fortygigabitether

Network OS Command Reference 101953-1003115-01show running-config interface fortygigabitethernet dot1x2dot1x reauthMax 5dot1x reauthenticationdot1x ti

1020 Network OS Command Reference53-1003115-01show running-config interface fortygigabitethernet fabric2show running-config interface fortygigabitethe

Network OS Command Reference 102153-1003115-01show running-config interface fortygigabitethernet fcoeport2show running-config interface fortygigabitet

68 Network OS Command Reference53-1003115-01certutil import syslogca2certutil import syslogcaImports a syslog CA certificate.Synopsis certutil import

1022 Network OS Command Reference53-1003115-01show running-config interface fortygigabitethernet lacp2show running-config interface fortygigabitethern

Network OS Command Reference 102353-1003115-01show running-config interface fortygigabitethernet lldp2show running-config interface fortygigabitethern

1024 Network OS Command Reference53-1003115-01show running-config interface fortygigabitethernet mac2show running-config interface fortygigabitetherne

Network OS Command Reference 102553-1003115-01show running-config interface fortygigabitethernet mtu2show running-config interface fortygigabitetherne

1026 Network OS Command Reference53-1003115-01show running-config interface fortygigabitethernet port-profile-port2show running-config interfaceforty

Network OS Command Reference 102753-1003115-01show running-config interface fortygigabitethernet priority-tag2show running-config interfacefortygigab

1028 Network OS Command Reference53-1003115-01show running-config interface fortygigabitethernet qos2show running-config interface fortygigabitetherne

Network OS Command Reference 102953-1003115-01show running-config interface fortygigabitethernet rmon2show running-config interface fortygigabitethern

1030 Network OS Command Reference53-1003115-01show running-config interface fortygigabitethernet sflow2show running-config interface fortygigabitether

Network OS Command Reference 103153-1003115-01show running-config interface fortygigabitethernet shutdown2show running-config interfacefortygigabitet

Network OS Command Reference 6953-1003115-01certutil import syslogca2The following command deletes a syslog CA certificate:switch# no certutil syslogc

1032 Network OS Command Reference53-1003115-01show running-config interface fortygigabitethernet switchport2show running-config interfacefortygigabit

Network OS Command Reference 103353-1003115-01show running-config interface fortygigabitethernet udld2show running-config interface fortygigabitethern

1034 Network OS Command Reference53-1003115-01show running-config interface fortygigabitethernet vlan2show running-config interface fortygigabitethern

Network OS Command Reference 103553-1003115-01show running-config interface gigabitethernet2show running-config interface gigabitethernetDisplays the

1036 Network OS Command Reference53-1003115-01show running-config interface gigabitethernet bpdu-drop2show running-config interface gigabitethernet bp

Network OS Command Reference 103753-1003115-01show running-config interface gigabitethernet channel-group2show running-config interfacegigabitetherne

1038 Network OS Command Reference53-1003115-01show running-config interface gigabitethernet description2show running-config interface gigabitethernet

Network OS Command Reference 103953-1003115-01show running-config interface gigabitethernet dot1x2show running-config interface gigabitethernet dot1xD

1040 Network OS Command Reference53-1003115-01show running-config interface gigabitethernet dot1x2 dot1x port-control auto dot1x quiet-period 120 dot1

Network OS Command Reference 104153-1003115-01show running-config interface gigabitethernet lacp2show running-config interface gigabitethernet lacpDis

70 Network OS Command Reference53-1003115-01channel-group2channel-groupEnables Link Aggregation on an interface.Synopsis channel-group number mode {ac

1042 Network OS Command Reference53-1003115-01show running-config interface gigabitethernet lldp2show running-config interface gigabitethernet lldpDis

Network OS Command Reference 104353-1003115-01show running-config interface gigabitethernet mac2show running-config interface gigabitethernet macDispl

1044 Network OS Command Reference53-1003115-01show running-config interface gigabitethernet mtu2show running-config interface gigabitethernet mtuDispl

Network OS Command Reference 104553-1003115-01show running-config interface gigabitethernet port-profile-port2show running-config interfacegigabiteth

1046 Network OS Command Reference53-1003115-01show running-config interface gigabitethernet priority-tag2show running-config interface gigabitethernet

Network OS Command Reference 104753-1003115-01show running-config interface gigabitethernet qos2show running-config interface gigabitethernet qosDispl

1048 Network OS Command Reference53-1003115-01show running-config interface gigabitethernet rmon2show running-config interface gigabitethernet rmonDis

Network OS Command Reference 104953-1003115-01show running-config interface gigabitethernet sflow2show running-config interface gigabitethernet sflowD

1050 Network OS Command Reference53-1003115-01show running-config interface gigabitethernet shutdown2show running-config interface gigabitethernet shu

Network OS Command Reference 105153-1003115-01show running-config interface gigabitethernet switchport2show running-config interface gigabitethernet s

Network OS Command Reference 7153-1003115-01channel-group2See Also interface

1052 Network OS Command Reference53-1003115-01show running-config interface gigabitethernet udld2show running-config interface gigabitethernet udldDis

Network OS Command Reference 105353-1003115-01show running-config interface gigabitethernet vlan2show running-config interface gigabitethernet vlanDis

1054 Network OS Command Reference53-1003115-01show running-config interface management2show running-config interface managementDisplays the management

Network OS Command Reference 105553-1003115-01show running-config interface port-channel2show running-config interface port-channelDisplays the status

1056 Network OS Command Reference53-1003115-01show running-config interface tengigabitethernet2show running-config interface tengigabitethernetDisplay

Network OS Command Reference 105753-1003115-01show running-config interface tengigabitethernet bpdu-drop2show running-config interfacetengigabitether

1058 Network OS Command Reference53-1003115-01show running-config interface tengigabitethernet cee2show running-config interface tengigabitethernet ce

Network OS Command Reference 105953-1003115-01show running-config interface tengigabitethernet channel-group2show running-config interfacetengigabite

1060 Network OS Command Reference53-1003115-01show running-config interface tengigabitethernet description2show running-config interfacetengigabiteth

Network OS Command Reference 106153-1003115-01show running-config interface tengigabitethernet dot1x2show running-config interface tengigabitethernet

Network OS Command Reference xi53-1003115-01fips root disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .286fips selftes

72 Network OS Command Reference53-1003115-01chassis beacon2chassis beaconControls the flashing LED beacon on the switch.Synopsis chassis beacon {enabl

1062 Network OS Command Reference53-1003115-01show running-config interface tengigabitethernet dot1x2dot1x reauthMax 5dot1x reauthenticationdot1x time

Network OS Command Reference 106353-1003115-01show running-config interface tengigabitethernet fabric2show running-config interface tengigabitethernet

1064 Network OS Command Reference53-1003115-01show running-config interface tengigabitethernet fcoeport2show running-config interface tengigabitethern

Network OS Command Reference 106553-1003115-01show running-config interface tengigabitethernet lacp2show running-config interface tengigabitethernet l

1066 Network OS Command Reference53-1003115-01show running-config interface tengigabitethernet lldp2show running-config interface tengigabitethernet l

Network OS Command Reference 106753-1003115-01show running-config interface tengigabitethernet mac2show running-config interface tengigabitethernet ma

1068 Network OS Command Reference53-1003115-01show running-config interface tengigabitethernet mtu2show running-config interface tengigabitethernet mt

Network OS Command Reference 106953-1003115-01show running-config interface tengigabitethernet port-profile-port2show running-config interfacetengiga

1070 Network OS Command Reference53-1003115-01show running-config interface tengigabitethernet priority-tag2show running-config interfacetengigabitet

Network OS Command Reference 107153-1003115-01show running-config interface tengigabitethernet qos2show running-config interface tengigabitethernet qo

Network OS Command Reference 7353-1003115-01chassis disable2chassis disableDisables all interfaces in the chassis.Synopsis chassis disable Operands No

1072 Network OS Command Reference53-1003115-01show running-config interface tengigabitethernet rmon2show running-config interface tengigabitethernet r

Network OS Command Reference 107353-1003115-01show running-config interface tengigabitethernet sflow2show running-config interface tengigabitethernet

1074 Network OS Command Reference53-1003115-01show running-config interface tengigabitethernet shutdown2show running-config interfacetengigabitethern

Network OS Command Reference 107553-1003115-01show running-config interface tengigabitethernet switchport2show running-config interfacetengigabitethe

1076 Network OS Command Reference53-1003115-01show running-config interface tengigabitethernet udld2show running-config interface tengigabitethernet u

Network OS Command Reference 107753-1003115-01show running-config interface tengigabitethernet vlan2show running-config interface tengigabitethernet v

1078 Network OS Command Reference53-1003115-01show running-config interface vlan2show running-config interface vlanDisplays the status of VLAN interfa

Network OS Command Reference 107953-1003115-01show running-config interface vlan ip2show running-config interface vlan ipDisplays the IP configuration

1080 Network OS Command Reference53-1003115-01show running-config interface vlan ip2• On Brocade VDX 8770 switches: 1 through 4086 for 802.1Q VLANs (V

Network OS Command Reference 108153-1003115-01show running-config ip access-list2show running-config ip access-listDisplays the configuration for the

74 Network OS Command Reference53-1003115-01chassis enable2chassis enableEnables all interfaces in the chassis.Synopsis chassis enable Operands NoneDe

1082 Network OS Command Reference53-1003115-01show running-config ip dns2show running-config ip dnsDisplays the domain name service (DNS) parameters.

Network OS Command Reference 108353-1003115-01show running-config ip igmp2show running-config ip igmpDisplays IGMP configuration information.Synopsis

1084 Network OS Command Reference53-1003115-01show running-config ip route2show running-config ip routeDisplays routing information.Synopsis show runn

Network OS Command Reference 108553-1003115-01show running-config ldap-server2show running-config ldap-serverDisplays the SSH server status in the run

1086 Network OS Command Reference53-1003115-01show running-config line2show running-config lineDisplays command line session configuration information

Network OS Command Reference 108753-1003115-01show running-config logging2show running-config loggingDisplays the log configurationSynopsis show runni

1088 Network OS Command Reference53-1003115-01show running-config logging auditlog class2show running-config logging auditlog classDisplays the severi

Network OS Command Reference 108953-1003115-01show running-config logging raslog2show running-config logging raslogDisplays the severity level configu

1090 Network OS Command Reference53-1003115-01show running-config logging syslog-facility2show running-config logging syslog-facilityDisplays the sysl

Network OS Command Reference 109153-1003115-01show running-config logging syslog-server2show running-config logging syslog-serverDisplays the syslog s

Network OS Command Reference 7553-1003115-01chassis fan airflow-direction2chassis fan airflow-directionSpecifies the direction of airflow through the

1092 Network OS Command Reference53-1003115-01show running-config mac-address-table2show running-config mac-address-tableDisplays configuration inform

Network OS Command Reference 109353-1003115-01show running-config monitor2show running-config monitor Displays configuration information about the mon

1094 Network OS Command Reference53-1003115-01show running-config ntp2show running-config ntpDisplays the Network Time Protocol (NTP) server configura

Network OS Command Reference 109553-1003115-01show running-config password-attributes2show running-config password-attributesDisplays global password

1096 Network OS Command Reference53-1003115-01show running-config police-priority-map2show running-config police-priority-mapDisplays configured polic

Network OS Command Reference 109753-1003115-01show running-config policy-map2show running-config policy-mapDisplays the currently running policy-map c

1098 Network OS Command Reference53-1003115-01show running-config port-profile2show running-config port-profileDisplays configured AMPP port-profiles.

Network OS Command Reference 109953-1003115-01show running-config port-profile activate2show running-config port-profile activateDisplays activated AM

1100 Network OS Command Reference53-1003115-01show running-config port-profile fcoe-profile2show running-config port-profile fcoe-profile Displays the

Network OS Command Reference 110153-1003115-01show running-config port-profile qos-profile2show running-config port-profile qos-profile Displays the c

76 Network OS Command Reference53-1003115-01chassis virtual-ip virtual-ipv62chassis virtual-ip virtual-ipv6Sets the IPv4 or IPv6 address of a switch c

1102 Network OS Command Reference53-1003115-01show running-config port-profile security-profile2show running-config port-profile security-profile Disp

Network OS Command Reference 110353-1003115-01show running-config port-profile static2show running-config port-profile static Displays statically asso

1104 Network OS Command Reference53-1003115-01show running-config port-profile vlan-profile2show running-config port-profile vlan-profile Displays inf

Network OS Command Reference 110553-1003115-01show running-config port-profile vlan-profile2Usage Guidelines On the Brocade VDX family of switches, VL

1106 Network OS Command Reference53-1003115-01show running-config port-profile-domain2show running-config port-profile-domainDisplays the port-profile

Network OS Command Reference 110753-1003115-01show running-config protocol cdp2show running-config protocol cdpDisplays the Cisco Discovery Protocol (

1108 Network OS Command Reference53-1003115-01show running-config protocol edge2show running-config protocol edgeDisplays the Edge Loop Detection (ELD

Network OS Command Reference 110953-1003115-01show running-config protocol lldp2show running-config protocol lldp Displays the Link Layer Discovery Pr

1110 Network OS Command Reference53-1003115-01show running-config protocol spanning-tree mstp2show running-config protocol spanning-tree mstpDisplays

Network OS Command Reference 111153-1003115-01show running-config protocol spanning-tree pvst2show running-config protocol spanning-tree pvstDisplays

Network OS Command Reference 7753-1003115-01cidrecov2cidrecovRecovers data from Chassis ID cards if possible.Synopsis cidrecov Operands There are no o

1112 Network OS Command Reference53-1003115-01show running-config protocol spanning-tree rpvst2show running-config protocol spanning-tree rpvstDisplay

Network OS Command Reference 111353-1003115-01show running-config protocol spanning-tree rstp2show running-config protocol spanning-tree rstpDisplays

1114 Network OS Command Reference53-1003115-01show running-config protocol spanning-tree stp2show running-config protocol spanning-tree stpDisplays th

Network OS Command Reference 111553-1003115-01show running-config protocol udld2show running-config protocol udldDisplays the UDLD global parameters.S

1116 Network OS Command Reference53-1003115-01show running-config radius-server2show running-config radius-serverDisplays the local switch configurati

Network OS Command Reference 111753-1003115-01show running-config rbridge-id2show running-config rbridge-idDisplays configuration for the RBridge ID.S

1118 Network OS Command Reference53-1003115-01show running-config rbridge-id linecard2show running-config rbridge-id linecardDisplays the interface mo

Network OS Command Reference 111953-1003115-01show running-config rbridge-id ssh2show running-config rbridge-id sshDisplays the Secure Shell (SSH) con

1120 Network OS Command Reference53-1003115-01show running-config rmon2show running-config rmonDisplays Remote Monitor configuration information.Synop

Network OS Command Reference 112153-1003115-01show running-config role2show running-config roleDisplays the configured roles.Synopsis show running-con

78 Network OS Command Reference53-1003115-01cidrecov2IP address Record 1 on CID 11st IP Address: 10.17.19.531st IP Mask: 255.255.240.02nd IP Address:

1122 Network OS Command Reference53-1003115-01show running-config route-map2show running-config route-mapDisplays the status of a route-map applicatio

Network OS Command Reference 112353-1003115-01show running-config rule2show running-config ruleDisplays configured access rules. Synopsis show running

1124 Network OS Command Reference53-1003115-01show running-config rule2To display a single rule:switch# show running-config rule 30 rule 30 action acc

Network OS Command Reference 112553-1003115-01show running-config secpolicy2show running-config secpolicyDisplays the Switch Connection Control (SCC)

1126 Network OS Command Reference53-1003115-01show running-config secpolicy2 ! member-entry 22:22:22:22:22:22:22:22 ! member-entry 33:33:33:33:33:33:3

Network OS Command Reference 112753-1003115-01show running-config sflow2show running-config sflowDisplays the IPv4 and IPv6 addresses and ports of sFl

1128 Network OS Command Reference53-1003115-01show running-config sflow-policy2show running-config sflow-policyDisplays the configured sFlow policies.

Network OS Command Reference 112953-1003115-01show running-config sflow-profile2show running-config sflow-profileDisplays the configured sFlow policie

1130 Network OS Command Reference53-1003115-01show running-config snmp-server2show running-config snmp-serverShows the running configuration of the SN

Network OS Command Reference 113153-1003115-01show running-config snmp-server engineid2show running-config snmp-server engineidShows the engine ID of

Network OS Command Reference 7953-1003115-01cidrecov2Example 3: Critical SEEPROM data is mismatched, recovery is not possible:sw0# cidrecov CID 1 and

1132 Network OS Command Reference53-1003115-01show running-config ssh2show running-config sshDisplays the Secure Shell (SSH) status in the running-con

Network OS Command Reference 113353-1003115-01show running-config ssh server2show running-config ssh serverDisplays the SSH server status in the runni

1134 Network OS Command Reference53-1003115-01show running-config ssh server2When SSH Server Key-exchange is configured to DH Group 14:switch# show ru

Network OS Command Reference 113553-1003115-01show running-config ssh server key-exchange2show running-config ssh server key-exchangeDisplays the SSH

1136 Network OS Command Reference53-1003115-01show running-config support2show running-config supportDisplays the support parameters in the running co

Network OS Command Reference 113753-1003115-01show running-config support autoupload-param2show running-config support autoupload-param Displays autou

1138 Network OS Command Reference53-1003115-01show running-config switch-attributes2show running-config switch-attributesDisplays switch attributes.Sy

Network OS Command Reference 113953-1003115-01show running-config system-monitor2show running-config system-monitorDisplays the system monitor configu

1140 Network OS Command Reference53-1003115-01show running-config system-monitor-mail2show running-config system-monitor-mailDisplays the system monit

Network OS Command Reference 114153-1003115-01show running-config tacacs-server2show running-config tacacs-serverDisplays the TACACS+ server configura

80 Network OS Command Reference53-1003115-01cipherset2ciphersetConfigures FIPS-compliant ciphers for LDAP and SSH protocols.Synopsis cipherset {ldap |

1142 Network OS Command Reference53-1003115-01show running-config telnet server2show running-config telnet serverDisplays the Telnet server status in

Network OS Command Reference 114353-1003115-01show running-config threshold-monitor2show running-config threshold-monitorDisplays the system’s thresho

1144 Network OS Command Reference53-1003115-01show running-config threshold-monitor interface2show running-config threshold-monitor interfaceDisplays

Network OS Command Reference 114553-1003115-01show running-config threshold-monitor security2show running-config threshold-monitor securityDisplays th

1146 Network OS Command Reference53-1003115-01show running-config threshold-monitor sfp2show running-config threshold-monitor sfpDisplays the system’s

Network OS Command Reference 114753-1003115-01show running-config username2show running-config usernameDisplays the user accounts on the switch.Synops

1148 Network OS Command Reference53-1003115-01show running-config vcs2show running-config vcsDisplays VCS configuration information.Synopsis show runn

Network OS Command Reference 114953-1003115-01show running-config zoning2show running-config zoning Displays the zoning configuration.Synopsis show ru

1150 Network OS Command Reference53-1003115-01show running-config zoning defined-configuration2show running-config zoning defined-configurationDisplay

Network OS Command Reference 115153-1003115-01show running-config zoning defined-configuration2zoning defined-configuration zone zone1 member-entry 11

Network OS Command Reference 8153-1003115-01cisco-interoperability2cisco-interoperabilityConfigures the switch to interoperate with some legacy Cisco

1152 Network OS Command Reference53-1003115-01show running-config zoning enabled-configuration2show running-config zoning enabled-configurationDisplay

Network OS Command Reference 115353-1003115-01show running-config zoning enabled-configuration2See Also show running-config zoning, show running-confi

1154 Network OS Command Reference53-1003115-01show running-config nas server-ip2show running-config nas server-ip Displays information about the speci

Network OS Command Reference 115553-1003115-01show secpolicy2show secpolicyDisplays the Switch Connection Control (SCC) security policy information.Sy

1156 Network OS Command Reference53-1003115-01show sflow2show sflow Displays sFlow configuration information and statistics.Synopsis show sflow [inter

Network OS Command Reference 115753-1003115-01show sflow2Actual sampling rate: 32768 pktsCounter polling interval: 20 secondsSamples received from har

1158 Network OS Command Reference53-1003115-01show sflow-profile2show sflow-profile Displays the sflow profile configurations.Synopsis show sflow-prof

Network OS Command Reference 115953-1003115-01show sfm2show sfmDisplays information about the switch fabric modules present in the chassis.Synopsis sh

1160 Network OS Command Reference53-1003115-01show sfm2 S2 SFM Switch Fabric Module 113 ENABLED# S3 SFM Switch Fabric Module 113 ENABLED # = At le

Network OS Command Reference 116153-1003115-01show sfp2show sfp Displays the SFP breakout configurations.Synopsis show sfp [linecard linecard [port po

xii Network OS Command Reference53-1003115-01ip community-list standard . . . . . . . . . . . . . . . . . . . . . . . . . . . .346ip dhcp relay addres

82 Network OS Command Reference53-1003115-01class2classCreates a class-map in a policy-map and enters the class-map configuration mode. he class-map m

1162 Network OS Command Reference53-1003115-01show slots2show slotsDisplays information about the modules present in the chassis.Synopsis show slots O

Network OS Command Reference 116353-1003115-01show slots2DISABLED The module is powered on but disabled.FAULTY The module is faulty because an error w

1164 Network OS Command Reference53-1003115-01show span path2show span pathDisplays the SPAN path information.Synopsis show span path session session_

Network OS Command Reference 116553-1003115-01show spanning-tree2show spanning-treeDisplays all Spanning Tree Protocol (STP) information.Synopsis show

1166 Network OS Command Reference53-1003115-01show spanning-tree brief2show spanning-tree briefDisplays the status and parameters of the Spanning Tree

Network OS Command Reference 116753-1003115-01show spanning-tree brief2Typical output of a summary that contains an rbridge-id as a non-root port.swit

1168 Network OS Command Reference53-1003115-01show spanning-tree interface2show spanning-tree interface Displays the state of the Spanning Tree Protoc

Network OS Command Reference 116953-1003115-01show spanning-tree interface2 Bridge Id: 8000.0005.1e76.1aa0 Port Te 0/0 enabled IfIndex: 67108864; Id:

1170 Network OS Command Reference53-1003115-01show spanning-tree mst brief2show spanning-tree mst briefDisplays the status and parameters of the Multi

Network OS Command Reference 117153-1003115-01show spanning-tree mst detail2show spanning-tree mst detail Displays details on an interface for the Mul

Network OS Command Reference 8353-1003115-01class2NOTEThe cir and cbs parameters are the mandatory for configuring a class-map. Other parameters are o

1172 Network OS Command Reference53-1003115-01show spanning-tree mst detail2 Number of topology change(s): 0 Bpdu-guard errdisable timeout: disabled B

Network OS Command Reference 117353-1003115-01show spanning-tree mst detail2 Port Te 1/0/20 enabled IfIndex: 68420100; Id: 8014; Role: Disabled; State

1174 Network OS Command Reference53-1003115-01show spanning-tree mst instance2show spanning-tree mst instance Displays information on a specified Mult

Network OS Command Reference 117553-1003115-01show spanning-tree mst instance2MSTI Bridge Id: 8001.0005.1e76.1aa0MSTI Bridge Priority: 32768See Also s

1176 Network OS Command Reference53-1003115-01show spanning-tree mst interface2show spanning-tree mst interface Displays information for a specified i

Network OS Command Reference 117753-1003115-01show spanning-tree mst interface2Instance Role Sts Cost Prio VLANs -----------------------------------

1178 Network OS Command Reference53-1003115-01show ssh server status2show ssh server statusDisplays the current Secure Shell (SSH) server key-exchange

Network OS Command Reference 117953-1003115-01show ssh server rekey-interval status2show ssh server rekey-interval statusDisplays the status informati

1180 Network OS Command Reference53-1003115-01show startup-config2show startup-configDisplays the contents of the startup configuration.Synopsis show

Network OS Command Reference 118153-1003115-01show startup-db2show startup-db Displays the startup database information.Synopsis show startup-db Opera

84 Network OS Command Reference53-1003115-01class-map2class-mapEnters class-map configuration mode.Synopsis class-map class-map-name no class-map clas

1182 Network OS Command Reference53-1003115-01show statistics access-list2show statistics access-listDisplays the statistics of an access-list status,

Network OS Command Reference 118353-1003115-01show statistics access-list2seq 81 hard-drop ip 10.10.75.0 0.0.0.0 10.10.0.0 0.0.255.255 count log (0 fr

1184 Network OS Command Reference53-1003115-01show statistics access-list interface2show statistics access-list interfaceDisplays the statistical info

Network OS Command Reference 118553-1003115-01show storm-control2show storm-controlDisplays information for traffic controlled by configured rate limi

1186 Network OS Command Reference53-1003115-01show storm-control2To display storm-control information for all traffic on the 10-gigabit Ethernet inter

Network OS Command Reference 118753-1003115-01show support2show supportDisplays a list of core files on the switch.Synopsis show support [rbridge-id {

1188 Network OS Command Reference53-1003115-01show system2show systemDisplays system information.Synopsis show system {rbridge-id rbridge-id}Operands

Network OS Command Reference 118953-1003115-01show system internal nas2show system internal nasDisplays all NAS server IP addresses in the system.Syno

1190 Network OS Command Reference53-1003115-01show system monitor2show system monitorDisplays the overall status for a selected switch.Synopsis show s

Network OS Command Reference 119153-1003115-01show telnet server status2show telnet server statusDisplays the current Telnet server status.Synopsis sh

Network OS Command Reference 8553-1003115-01clear arp2clear arpClears the ARP statistics cache on the host. Synopsis clear arp [interface gigabitether

1192 Network OS Command Reference53-1003115-01show threshold monitor2show threshold monitorDisplays the current status of environmental thresholds and

Network OS Command Reference 119353-1003115-01show udld2show udldShows global UDLD information.Synopsis show udldOperands NoneDefaults NoneCommand Mod

1194 Network OS Command Reference53-1003115-01show udld interface2show udld interfaceShows UDLD information for interfaces.Synopsis show udld interfac

Network OS Command Reference 119553-1003115-01show udld interface2Examples To display UDLD information for a specific 10-gigabitEthernet interface:swi

1196 Network OS Command Reference53-1003115-01show udld statistics2show udld statisticsShows UDLD statistics.Synopsis show udld statistics [interface

Network OS Command Reference 119753-1003115-01show users2show usersDisplays the users logged in to the system and locked user accounts.Synopsis show u

1198 Network OS Command Reference53-1003115-01show vcs2show vcsDisplays the Brocade VCS Fabric configuration. Synopsis show vcs {detail | virtual-ip}

Network OS Command Reference 119953-1003115-01show vcs2Co-ordinator : NOWWN : 10:00:00:05:33:78:00:00Switch MAC : 00:05:33:78:00:81FCF MAC : 19:30:0

1200 Network OS Command Reference53-1003115-01show vcs2 FCF MAC : 00:05:1E:CD:22:6A Switch Type : VDX6720-24 Firmware Ver

Network OS Command Reference 120153-1003115-01show version2show versionDisplays the current firmware version.Synopsis show version [rbridge-id {rbridg

86 Network OS Command Reference53-1003115-01clear arp2• On Brocade VDX 8770 switches: 1 through 4086 for 802.1Q VLANs (VLAN IDs 4087 through 4095 are

1202 Network OS Command Reference53-1003115-01show version24.1.0 L1/0 NOS 4.1.0 ACTIVE4.1.0 L1/1 NOS 4.1.0 STANDBY4.1.0 L2/0 NOS 4.1.0 ACTIVE4.

Network OS Command Reference 120353-1003115-01show virtual-fabric status2show virtual-fabric statusDisplays the status of the Virtual Fabric (VF): VF-

1204 Network OS Command Reference53-1003115-01show vlan2show vlanDisplays information about a specific VLAN interface.Synopsis show vlan [vlan_id | br

Network OS Command Reference 120553-1003115-01show vlan2• The following example shows all VLANs that are configured, provisioned (active) and unprovis

1206 Network OS Command Reference53-1003115-01show vlan2• The following example shows only unprovisioned VLANs:switch# show vlan brief unprovisionedTo

Network OS Command Reference 120753-1003115-01show vlan classifier2show vlan classifier Displays information about a specific VLAN classifier group.Sy

1208 Network OS Command Reference53-1003115-01show vlan private-vlan2show vlan private-vlanDisplays information about private VLANs.Synopsis show vlan

Network OS Command Reference 120953-1003115-01show vlan rspan-vlan2show vlan rspan-vlanDisplays information about remote SPAN VLANs.Synopsis show vlan

1210 Network OS Command Reference53-1003115-01show vnetwork2show vnetworkDisplays virtual assets from the vCenter that are discovered on a Brocade VDX

Network OS Command Reference 121153-1003115-01show vnetwork2vcenter Selects a vCenter (required).vms Displays discovered VMs.vss Displays discovered s

Network OS Command Reference 8753-1003115-01clear counters2clear countersClears the IP counter statistics on the switch.Synopsis clear counters [acces

1212 Network OS Command Reference53-1003115-01show vnetwork2switch# show vnetwork pgs PortGroup vSwitch vlanId Host============ =============== =====

Network OS Command Reference 121353-1003115-01show vrf2show vrfDisplays VRF configuration information.Synopsis show vrf Operands NoneDefaults None Com

1214 Network OS Command Reference53-1003115-01show vrrp2show vrrp Displays information about VRRP and VRRP-E sessions.Synopsis show vrrp VRID [detail]

Network OS Command Reference 121553-1003115-01show vrrp2Interface: Ten Gigabit Ethernet 0/18; Ifindex: 403832850Mode: VRRPAdmin Status: EnabledAddress

1216 Network OS Command Reference53-1003115-01show zoning enabled-configuration2show zoning enabled-configurationDisplays information about the enable

Network OS Command Reference 121753-1003115-01show zoning operation-info2show zoning operation-infoDisplays information about transactions and databas

1218 Network OS Command Reference53-1003115-01shutdown2shutdown Disables the selected interface.Synopsis shutdown no shutdown Operands NoneDefaults Th

Network OS Command Reference 121953-1003115-01shutdown (UDLD)2shutdown (UDLD)Disables the unidirectional link detection (UDLD) protocol on all ports.S

1220 Network OS Command Reference53-1003115-01shutdown (STP)2shutdown (STP)Disables the Multiple Spanning Tree Protocol (MSTP), Rapid Spanning Tree Pr

Network OS Command Reference 122153-1003115-01shutdown-time2shutdown-timeSpecifies the time a port will be disabled after Edge Loop Detection (ELD) de

88 Network OS Command Reference53-1003115-01clear counters2Description Use this command to clear the counter statistics on the switch.Usage Guidelines

1222 Network OS Command Reference53-1003115-01slot2slotEnables or disables the slot.Synopsis slot number {disable | enable}Operands number The slot to

Network OS Command Reference 122353-1003115-01snmp-server community2snmp-server communitySets or removes the community string and read-write or read-o

1224 Network OS Command Reference53-1003115-01snmp-server contact2snmp-server contactSets the SNMP server contact string.Synopsis snmp-server contact

Network OS Command Reference 122553-1003115-01snmp-server context2snmp-server context Maps the context name in an SNMPv3 packet’s protocol data unit (

1226 Network OS Command Reference53-1003115-01snmp-server engineid local2snmp-server engineid localConfigures a user-defined engine ID for the SNMP ag

Network OS Command Reference 122753-1003115-01snmp-server host2snmp-server hostSets the trap destination IP addresses, version, community string (for

1228 Network OS Command Reference53-1003115-01snmp-server host2 The no snmp-server host host community-string string version 2c command brings version

Network OS Command Reference 122953-1003115-01snmp-server location2snmp-server locationSets the SNMP server location string. Synopsis snmp-server loca

1230 Network OS Command Reference53-1003115-01snmp-server sys-descr2snmp-server sys-descr Sets the Management Information Base (MIB-2) object identifi

Network OS Command Reference 123153-1003115-01snmp-server user2snmp-server userCreates or changes the attributes of SNMPv3 users.Synopsis snmp-server

Network OS Command Reference 8953-1003115-01clear counters access-list2clear counters access-listClears the IP counter statistics on all interfaces on

1232 Network OS Command Reference53-1003115-01snmp-server user2Description Use this command to configure SNMPv3 users that can be associated with a tr

Network OS Command Reference 123353-1003115-01snmp-server v3host2snmp-server v3host Specifies the recipient of the SNMPv3 notification parameter.Synop

1234 Network OS Command Reference53-1003115-01source2sourceConfigures the monitoring session.Synopsis source [fortygigabitethernet rbridge-id/slot/por

Network OS Command Reference 123553-1003115-01source2slot Specifies a valid slot number.port Specifies a valid port number.direction rx Specifies to m

1236 Network OS Command Reference53-1003115-01spanning-tree autoedge2spanning-tree autoedgeEnables automatic edge detection.Synopsis spanning-tree aut

Network OS Command Reference 123753-1003115-01spanning-tree bpdu-mac2spanning-tree bpdu-mac Sets the MAC address of the Bridge Protocol Data Unit (BPD

1238 Network OS Command Reference53-1003115-01spanning-tree cost2spanning-tree cost Changes an interface's spanning-tree port path cost.Synopsis

Network OS Command Reference 123953-1003115-01spanning-tree edgeport2spanning-tree edgeport Enables the edge port on an interface to allow the interfa

1240 Network OS Command Reference53-1003115-01spanning-tree guard root2spanning-tree guard root Enables the guard root to restrict which interface is

Network OS Command Reference 124153-1003115-01spanning-tree guard root2See Also show spanning-tree

90 Network OS Command Reference53-1003115-01clear counters access-list2rbridge-id Specifies the RBridge ID. This is not valid in standalone mode.slot

1242 Network OS Command Reference53-1003115-01spanning-tree hello-time2spanning-tree hello-time Configures the hello-time in seconds on the interface.

Network OS Command Reference 124353-1003115-01spanning-tree instance2spanning-tree instance Sets restrictions for the port of particular MSTP instance

1244 Network OS Command Reference53-1003115-01spanning-tree link-type2spanning-tree link-typeEnables and disables the rapid transition for the Spannin

Network OS Command Reference 124553-1003115-01spanning-tree portfast2spanning-tree portfastEnables the Port Fast feature on an interface to allow the

1246 Network OS Command Reference53-1003115-01spanning-tree priority2spanning-tree priorityChanges an interface's spanning-tree port priority.Syn

Network OS Command Reference 124753-1003115-01spanning-tree restricted-role2spanning-tree restricted-roleRestricts the role of the port from becoming

1248 Network OS Command Reference53-1003115-01spanning-tree restricted-tcn2spanning-tree restricted-tcnRestricts the topology change notification Brid

Network OS Command Reference 124953-1003115-01spanning-tree shutdown2spanning-tree shutdownEnables or disables spanning tree on the interface.Synopsis

1250 Network OS Command Reference53-1003115-01spanning-tree vlan2spanning-tree vlanConfigures the VLAN identifier for the spanning tree interface.Syno

Network OS Command Reference 125153-1003115-01speed (Ethernet)2speed (Ethernet)Sets the speed on the Ethernet interface.Synopsis speed {10000 | 1000 |

Network OS Command Reference 9153-1003115-01clear counters access-list (interface)2clear counters access-list (interface)Clears the IP counter statist

1252 Network OS Command Reference53-1003115-01speed (Fibre Channel)2speed (Fibre Channel)Sets the operational speed of a Fibre Channel port.Synopsis s

Network OS Command Reference 125353-1003115-01speed (port-channel)2speed (port-channel)Sets the speed on the port-channel interface.Synopsis speed {10

1254 Network OS Command Reference53-1003115-01speed (LAG)2speed (LAG)Sets the speed on the LAG interface.Synopsis speed {1000 | 10000 | 40000} Operand

Network OS Command Reference 125553-1003115-01spt-threshold2spt-threshold Configures the Shortest Path Tree (SPT) threshold.Synopsis spt-threshold {in

1256 Network OS Command Reference53-1003115-01ssh2sshConnects to a remote server using the Secure Shell (SSH) protocol.Synopsis ssh [-c] [-l] [-m] {IP

Network OS Command Reference 125753-1003115-01ssh2To connect to a remote device using an SSH connection with a login name:switch# ssh -l admin 127.2.1

1258 Network OS Command Reference53-1003115-01ssh server key-exchange dh-group-142ssh server key-exchange dh-group-14Specifies the method used for gen

Network OS Command Reference 125953-1003115-01ssh server rekey-interval2ssh server rekey-intervalConfigures the Secure Shell (SSH) server rekey-interv

1260 Network OS Command Reference53-1003115-01ssh server shutdown2ssh server shutdownDisables SSH service on the switch.Synopsis ssh server shutdown n

Network OS Command Reference 126153-1003115-01ssh server status2ssh server statusDisplays SSH service on the switch.Synopsis ssh server status Operand

Network OS Command Reference xiii53-1003115-01ip route next-hop ospf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .395ip route next-h

92 Network OS Command Reference53-1003115-01clear counters access-list (interface)2Description Use this command to clear statistics on one or on all i

1262 Network OS Command Reference53-1003115-01static-network (BGP)2static-network (BGP)Configures a static BGP4 network, creating a stable network in

Network OS Command Reference 126353-1003115-01storm-control ingress2storm-control ingressLimits ingress traffic on a specified interface. Synopsis sto

1264 Network OS Command Reference53-1003115-01storm-control ingress2Enter no storm-control ingress to disable BUM storm control for a particular traff

Network OS Command Reference 126553-1003115-01summary-address2summary-addressConfigures route summarization for redistributed routes for an Autonomous

1266 Network OS Command Reference53-1003115-01support2support Enables or disables the first-fault data capture (FFDC).Synopsis support ffdc no support

Network OS Command Reference 126753-1003115-01support autoupload enable2support autoupload enableSpecifies if support autoupload is enabled or disable

1268 Network OS Command Reference53-1003115-01support autoupload-param2support autoupload-paramDefines autoupload parameters.Synopsis support autouplo

Network OS Command Reference 126953-1003115-01switch-attributes2switch-attributesSets switch attributes.Synopsis switch-attributes rbridge-id chassis-

1270 Network OS Command Reference53-1003115-01switchport2switchport Puts the interface in Layer 2 mode.Synopsis switchport no switchport Operands None

Network OS Command Reference 127153-1003115-01switchport access2switchport accessSets the Layer 2 interface as access.Synopsis switchport access {vlan

Network OS Command Reference 9353-1003115-01clear counters access-list (ip)2clear counters access-list (ip)Clears the IP ACL counters for all interfac

1272 Network OS Command Reference53-1003115-01switchport access2The following examples illustrate configuration with service or transport VFs in a Vir

Network OS Command Reference 127353-1003115-01switchport mode2switchport modeSets the mode of the interface.Synopsis switchport mode {access | trunk}

1274 Network OS Command Reference53-1003115-01switchport mode private-vlan2switchport mode private-vlanSets the private VLAN (PVLAN) mode of the Layer

Network OS Command Reference 127553-1003115-01switchport port-security2switchport port-securityEnables or disables port security on an interface port.

1276 Network OS Command Reference53-1003115-01switchport port-security mac-address2switchport port-security mac-address Configures the MAC address opt

Network OS Command Reference 127753-1003115-01switchport port-security max2switchport port-security max Configures the maximum number of MAC addresses

1278 Network OS Command Reference53-1003115-01switchport port-security oui2switchport port-security oui Configures an Organizationally Unique Identifi

Network OS Command Reference 127953-1003115-01switchport port-security shutdown-time2switchport port-security shutdown-time Configures the shutdown-ti

1280 Network OS Command Reference53-1003115-01switchport port-security sticky2switchport port-security sticky Converts dynamic MAC addresses to sticky

Network OS Command Reference 128153-1003115-01switchport port-security violation2switchport port-security violation Configures the violation response

94 Network OS Command Reference53-1003115-01clear counters access-list (ip)2interface Specifies the interface.out Specifies the egress direction.ve vl

1282 Network OS Command Reference53-1003115-01switchport private-vlan association trunk2switchport private-vlan association trunkAssigns a primary pri

Network OS Command Reference 128353-1003115-01switchport private-vlan host-association2switchport private-vlan host-associationAssigns a secondary and

1284 Network OS Command Reference53-1003115-01switchport private-vlan mapping2switchport private-vlan mappingMaps primary VLAN and secondary VLAN to a

Network OS Command Reference 128553-1003115-01switchport private-vlan trunk allowed vlan2switchport private-vlan trunk allowed vlanAdds a VLAN to a pr

1286 Network OS Command Reference53-1003115-01switchport private-vlan trunk allowed vlan2switch(config-if-te-2/0/2)# switchport private-vlan associati

Network OS Command Reference 128753-1003115-01switchport private-vlan trunk native-vlan2switchport private-vlan trunk native-vlanSets native private V

1288 Network OS Command Reference53-1003115-01switchport trunk allowed vlan rspan-vlan2switchport trunk allowed vlan rspan-vlanAdds or removes VLANs o

Network OS Command Reference 128953-1003115-01switchport trunk allowed vlan rspan-vlan2switch(config)# interface tengigabitethernet 178/0/9 switch(con

1290 Network OS Command Reference53-1003115-01switchport trunk default-vlan2switchport trunk default-vlanConfigures tagged or untagged data traffic th

Network OS Command Reference 129153-1003115-01switchport trunk native-vlan2switchport trunk native-vlanSets native VLAN characteristics as an 802.1Q V

Network OS Command Reference 9553-1003115-01clear counters access-list (MAC)2clear counters access-list (MAC)Clears all the Media Access Control (MAC)

1292 Network OS Command Reference53-1003115-01switchport trunk native-vlan2switch(conf-if-te-178/0/9)# switchport trunk native-vlan 120The following i

Network OS Command Reference 129353-1003115-01switchport trunk tag native-vlan2switchport trunk tag native-vlanEnables tagging on native VLAN traffic.

1294 Network OS Command Reference53-1003115-01system-description2system-descriptionSets the global system description specific to LLDP.Synopsis system

Network OS Command Reference 129553-1003115-01system-max2system-maxSets the maximum number of Address Resolution Protocol (ARP) requests that the syst

1296 Network OS Command Reference53-1003115-01system-monitor2system-monitor Manages the monitoring of FRUs and sets a variety of alerts when threshold

Network OS Command Reference 129753-1003115-01system-monitor2threshold Specifies the monitoring of thresholds down-threshold Specifies an integer valu

1298 Network OS Command Reference53-1003115-01system-monitor-mail2system-monitor-mailConfigures Fabric Watch e-mail alerts on the switch. Synopsis sys

Network OS Command Reference 129953-1003115-01system-monitor-mail2switch(config)# system-monitor-mail relay 1.2.3.4 domain-name abc.brocade.com switch

1300 Network OS Command Reference53-1003115-01system-name2system-name Sets the global system name specific to LLDP. Synopsis system-name name no syste

Network OS Command Reference 130153-1003115-01table-map (BGP)2table-map (BGP)Maps external entry attributes into the routing table, ensuring that thos

96 Network OS Command Reference53-1003115-01clear counters access-list (MAC)2Defaults NoneCommand Modes Privileged EXEC modeDescription Use this comma

1302 Network OS Command Reference53-1003115-01table-map (BGP)2switch(config-rbridge-id-10)# router bgpswitch(config-bgp-router)# address-family ipv4 u

Network OS Command Reference 130353-1003115-01tacacs-server2tacacs-serverConfigures a Terminal Access Controller Access-Control System plus (TACACS+)

1304 Network OS Command Reference53-1003115-01tacacs-server2Examples To configure an IPv4 TACACS+ server:switch(config)# tacacs-server host 10.24.65.6

Network OS Command Reference 130553-1003115-01tagged-ieee-bpdu-enabled2tagged-ieee-bpdu-enabledActivates IEEE BPDU packets.Synopsis tagged-ieee-bpdu-e

1306 Network OS Command Reference53-1003115-01tcp burstrate2tcp burstrate Sets the threshold for the burst rate of TCP traffic, and defines the locko

Network OS Command Reference 130753-1003115-01telnet2telnetEstablishes a Telnet session to a remote networking device.Synopsis telnet {IP Address | ho

1308 Network OS Command Reference53-1003115-01telnet server shutdown2telnet server shutdownDisables Telnet service on the switch.Synopsis telnet serve

Network OS Command Reference 130953-1003115-01terminal2terminalSets terminal parameters for the current session.Synopsis terminal [length number_of_li

1310 Network OS Command Reference53-1003115-01threshold-monitor cpu2threshold-monitor cpuConfigures monitoring of CPU usage of the system and alerts t

Network OS Command Reference 131153-1003115-01threshold-monitor interface2threshold-monitor interfaceConfigures monitoring of port statistics on all e

Network OS Command Reference 9753-1003115-01clear counters interface2clear counters interfaceClears the IP counter statistics on a specified interface

1312 Network OS Command Reference53-1003115-01threshold-monitor interface2area Enables policy configuration.CRCAlignErrors The total number of frames

Network OS Command Reference 131353-1003115-01threshold-monitor interface2none Compares a data value to a threshold boundary level.Defaults See Operan

1314 Network OS Command Reference53-1003115-01threshold-monitor memory2threshold-monitor memoryConfigures monitoring of the memory usage of the system

Network OS Command Reference 131553-1003115-01threshold-monitor memory2Examples switch(config-rbridge-id-154)# threshold-monitor memory actions none h

1316 Network OS Command Reference53-1003115-01threshold-monitor security2threshold-monitor security Configures monitoring of security parameters, such

Network OS Command Reference 131753-1003115-01threshold-monitor security2fence Specifies that Port Fencing is applied, which disables the port until f

1318 Network OS Command Reference53-1003115-01threshold-monitor sfp2threshold-monitor sfp Configures monitoring of SFP parameters.Synopsis threshold-m

Network OS Command Reference 131953-1003115-01threshold-monitor sfp2above Enables setting a value for highthresh-action, which specifies the action to

1320 Network OS Command Reference53-1003115-01threshold-monitor sfp2See Also rbridge-id

Network OS Command Reference 132153-1003115-01timeout fnm2timeout fnmFor Access Gateway mode, this sets and displays the fabric name monitoring time-o

98 Network OS Command Reference53-1003115-01clear counters interface2vlan vlan_id Specifies a VLAN interface. (Refer to the Usage Guidelines.)Command

1322 Network OS Command Reference53-1003115-01timers2timersConfigures Link State Advertisement (LSA) pacing and Shortest Path First (SPF) throttle tim

Network OS Command Reference 132353-1003115-01timers (BGP)2timers (BGP)Adjusts the interval at which BGP KEEPALIVE and HOLDTIME messages are sent.Syno

1324 Network OS Command Reference53-1003115-01traceroute2traceroute Traces the network path of packets as they are forwarded to a destination address.

Network OS Command Reference 132553-1003115-01track2trackSpecifies a VRRP interface to track.Synopsis track {fortygigabitethernet rbridge-id/slot/port

1326 Network OS Command Reference53-1003115-01track2Examples To set the track port to 21/2/4 and the track priority to 60:switch(config)# rbridge-id 2

Network OS Command Reference 132753-1003115-01transmit-holdcount2transmit-holdcountConfigures the maximum number of Bridge Protocol Data Units (BPDUs)

1328 Network OS Command Reference53-1003115-01transport-service2transport-serviceIn a Virtual Fabrics context, associates a service VF with a trunk po

Network OS Command Reference 132953-1003115-01trunk-enable2trunk-enableEnables trunking on a Fibre Channel port.Synopsis trunk-enable no trunk-enable

1330 Network OS Command Reference53-1003115-01udld enable2udld enableEnables the Unidirectional Link Detection (UDLD) protocol on an interface.Synopsi

Network OS Command Reference 133153-1003115-01unhide fips2unhide fipsMakes available irreversible commands used in enabling Federal Information Proces

Network OS Command Reference 9953-1003115-01clear counters slot-id2clear counters slot-idClears the IP counter statistics on a specified slot in the c

1332 Network OS Command Reference53-1003115-01unlock username2unlock usernameUnlocks a locked user account.Synopsis unlock username name [rbridge-id {

Network OS Command Reference 133353-1003115-01update-time (BGP)2update-time (BGP)Configures the interval at which BGP next-hop tables are modified.Syn

1334 Network OS Command Reference53-1003115-01usb2usb Enables or disables an attached USB device.Synopsis usb {on |off}Operands on Turns the USB devic

Network OS Command Reference 133553-1003115-01usb dir2usb dirLists the contents of an attached USB device.Synopsis usb dir Operands NoneDefaults NoneC

1336 Network OS Command Reference53-1003115-01usb remove2usb removeRemoves a file from an attached USB device.Synopsis usb remove directory directory

Network OS Command Reference 133753-1003115-01user (alias configuration)2user (alias configuration) Launches the user level alias configuration mode.S

1338 Network OS Command Reference53-1003115-01username2username Configures a user account.Synopsis username username password password role role_name

Network OS Command Reference 133953-1003115-01username2switch(config)# username userBrocade password ******** role user desc "User to monitor&quo

1340 Network OS Command Reference53-1003115-01username admin enable false2username admin enable false Toggles the lockout option for the default admin

Network OS Command Reference 134153-1003115-01username user enable false2username user enable falseToggles the lockout option for user accounts with a

100 Network OS Command Reference53-1003115-01clear counters (IP)2clear counters (IP) Clears the IP counter statistics on all interfaces on the switch.

1342 Network OS Command Reference53-1003115-01vc-link-init2vc-link-initSpecifies the fill word used on long distance links for an 8 Gbps Fibre Channel

Network OS Command Reference 134353-1003115-01vcenter2vcenterAuthenticates with an established vCenter and provides additional options.Synopsis vcente

1344 Network OS Command Reference53-1003115-01vcenter discovery (ignore delete responses)2vcenter discovery (ignore delete responses)Causes a vCenter

Network OS Command Reference 134553-1003115-01vcs (logical chassis cluster mode)2vcs (logical chassis cluster mode)Changes RBridge ID and/or VCS ID of

1346 Network OS Command Reference53-1003115-01vcs (logical chassis cluster mode)2The following provides examples of using the no form of this command.

Network OS Command Reference 134753-1003115-01vcs (standalone mode)2vcs (standalone mode)Configures Brocade VCS Fabric technology parameters and can e

1348 Network OS Command Reference53-1003115-01vcs (standalone mode)2The following provides command examples of enabling Brocade VCS fabric cluster mod

Network OS Command Reference 134953-1003115-01vcs config snapshot (logical chassis cluster mode)2vcs config snapshot (logical chassis cluster mode)Tak

1350 Network OS Command Reference53-1003115-01vcs logical-chassis enable (fabric cluster mode)2vcs logical-chassis enable (fabric cluster mode)Changes

Network OS Command Reference 135153-1003115-01vcs rbridge-id (fabric cluster mode)2vcs rbridge-id (fabric cluster mode)Changes the RBridge ID and, opt

Network OS Command Reference 10153-1003115-01clear counters (IP)2ve vlan_id Specifies the virtual Ethernet (VE) interface to which the ACL is bound.

1352 Network OS Command Reference53-1003115-01vcs vcsid (fabric cluster mode)2vcs vcsid (fabric cluster mode)Changes the VCS ID and, optionally, the R

Network OS Command Reference 135353-1003115-01vcs virtual-fabric enable2vcs virtual-fabric enableEnables the Virtual Fabrics feature, allowing the con

1354 Network OS Command Reference53-1003115-01vcs replace rbridge-id2vcs replace rbridge-idReplaces a node in a logical chassis cluster.Synopsis vcs r

Network OS Command Reference 135553-1003115-01vcs virtual ip2vcs virtual ipAssigns a single virtual IP address to all switches in a Brocade VCS Fabric

1356 Network OS Command Reference53-1003115-01virtual-fabric2virtual-fabricDesignates the FCoE Virtual Fabric Identification (VFID).Synopsis virtual-f

Network OS Command Reference 135753-1003115-01virtual-ip2virtual-ipConfigures a virtual IPv4 address for the virtual router.Synopsis virtual-ip A.B.C.

1358 Network OS Command Reference53-1003115-01vlag ignore-split2vlag ignore-splitControls the ignore-split recovery functionality.Synopsis vlag ignore

Network OS Command Reference 135953-1003115-01vlan classifier activate group2vlan classifier activate groupActivates a VLAN classifier group.Synopsis

1360 Network OS Command Reference53-1003115-01vlan classifier group2vlan classifier groupAdds and deletes rules to a VLAN classifier group.Synopsis vl

Network OS Command Reference 136153-1003115-01vlan classifier rule2vlan classifier ruleCreates a VLAN classifier rule.Synopsis vlan classifier rule ru

xiv Network OS Command Reference53-1003115-01mac-group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .446mac-rebala

102 Network OS Command Reference53-1003115-01clear counters (MAC)2clear counters (MAC)Clears the MAC counter statistics on all interfaces on the switc

1362 Network OS Command Reference53-1003115-01vlan dot1q tag native2vlan dot1q tag nativeEnables 802.1tagging on the native VLAN.Synopsis vlan dot1q t

Network OS Command Reference 136353-1003115-01vlan-profile (AMPP)2vlan-profile (AMPP) Activates the VLAN profile mode for AMPP. Synopsis vlan-profile

1364 Network OS Command Reference53-1003115-01vnetwork vcenter discover2vnetwork vcenter discoverExplicitly starts the discovery process on the vCente

Network OS Command Reference 136553-1003115-01vrf2vrfCreates and enters Virtual Routing and Forwarding (VRF) configuration mode.Synopsis vrf nameOpera

1366 Network OS Command Reference53-1003115-01vrf-lite-capability (OSPF)2vrf-lite-capability (OSPF)Disables the down-bit (DN bit) that is set when rou

Network OS Command Reference 136753-1003115-01vrrp-extended-group2vrrp-extended-groupConfigures a virtual-router-extended group.Synopsis vrrp-extended

1368 Network OS Command Reference53-1003115-01vrrp-group2vrrp-groupConfigures a virtual router group.Synopsis vrrp-group group-ID no vrrp-group group-

Network OS Command Reference 136953-1003115-01zoning defined-configuration alias2zoning defined-configuration aliasCreates or deletes a zone alias.Syn

1370 Network OS Command Reference53-1003115-01zoning defined-configuration alias2switch(config-alias-alias1)# member-entry 10:00:00:00:00:00:00:01 To

Network OS Command Reference 137153-1003115-01zoning defined-configuration cfg2zoning defined-configuration cfgCreates a new zone configuration or add

Network OS Command Reference 10353-1003115-01clear counters (MAC)2slot-id number Specifies the slot number of the linecard. Defaults NoneCommand Modes

1372 Network OS Command Reference53-1003115-01zoning defined-configuration cfg2NOTEZone aliases are not valid zone configuration members. Adding an al

Network OS Command Reference 137353-1003115-01zoning defined-configuration zone2zoning defined-configuration zoneCreates a new zone or adds a member t

1374 Network OS Command Reference53-1003115-01zoning defined-configuration zone2The zoning defined-configuration zone command changes the defined conf

Network OS Command Reference 137553-1003115-01zoning enabled-configuration cfg-action cfg-clear2zoning enabled-configuration cfg-action cfg-clearClear

1376 Network OS Command Reference53-1003115-01zoning enabled-configurationcfg-actioncfg-save2zoning enabled-configuration cfg-action cfg-saveSaves the

Network OS Command Reference 137753-1003115-01zoning enabled-configuration cfg-action cfg-transaction-abort2zoning enabled-configuration cfg-action c

1378 Network OS Command Reference53-1003115-01zoning enabled-configuration cfg-name2zoning enabled-configuration cfg-nameEnables a zone configuration.

Network OS Command Reference 137953-1003115-01zoning enabled-configuration default-zone-access2zoning enabled-configuration default-zone-accessSets th

1380 Network OS Command Reference53-1003115-01zoning enabled-configuration default-zone-access2

104 Network OS Command Reference53-1003115-01clear counters storm-control2clear counters storm-control Clears counters about traffic controlled by con

Network OS Command Reference 10553-1003115-01clear counters storm-control2To clear counters for all multicast traffic in the system:switch# clear coun

106 Network OS Command Reference53-1003115-01clear dot1x statistics2clear dot1x statisticsClears all dot1x statistics.Synopsis clear dot1x statistics

Network OS Command Reference 10753-1003115-01clear dot1x statistics interface2clear dot1x statistics interfaceClears the dot1x statistics for a port.S

108 Network OS Command Reference53-1003115-01clear edge-loop-detection2clear edge-loop-detectionRe-enables all ports disabled by ELD and clears all EL

Network OS Command Reference 10953-1003115-01clear edge-loop-detection2Examples NoneSee Also protocol edge-loop-detection, show edge-loop-detection in

110 Network OS Command Reference53-1003115-01clear fcoe login2clear fcoe login Clears the FCoE login for a given FCoE interface, vlan, vfid, or device

Network OS Command Reference 11153-1003115-01clear ip bgp dampening2clear ip bgp dampeningReactivates all suppressed BGP4 routes.Synopsis clear ip bgp

Network OS Command Reference xv53-1003115-01neighbor capability as4 (BGP) . . . . . . . . . . . . . . . . . . . . . . . . .494neighbor default-origin

112 Network OS Command Reference53-1003115-01clear ip bgp flap-statistics2clear ip bgp flap-statisticsClears the dampening statistics for a BGP4 route

Network OS Command Reference 11353-1003115-01clear ip bgp local routes2clear ip bgp local routesClears all BGP4 local routes from the IP route table a

114 Network OS Command Reference53-1003115-01clear ip bgp neighbor2clear ip bgp neighborRequests a dynamic refresh of BGP4 connections or routes from

Network OS Command Reference 11553-1003115-01clear ip bgp routes2clear ip bgp routesClears BGP4 routes from the IP route table and resets the routes.S

116 Network OS Command Reference53-1003115-01clear ip bgp traffic2clear ip bgp trafficClears the BGP4 message counter for all neighbors.Synopsis clear

Network OS Command Reference 11753-1003115-01clear ip dhcp relay statistics2clear ip dhcp relay statisticsClears IP DHCP Relay statisticsSynopsis clea

118 Network OS Command Reference53-1003115-01clear ip igmp groups2clear ip igmp groupsClears information related to learned groups in the IGMP module.

Network OS Command Reference 11953-1003115-01clear ip igmp groups2Usage Guidelines On the Brocade VDX family of switches, VLANs are treated as interfa

120 Network OS Command Reference53-1003115-01clear ip igmp statistics interface2clear ip igmp statistics interfaceClears statistical information relat

Network OS Command Reference 12153-1003115-01clear ip igmp statistics interface2• On Brocade VDX 8770 switches: 1 through 4086 for 802.1Q VLANs (VLAN

xvi Network OS Command Reference53-1003115-01port-profile (global configuration mode). . . . . . . . . . . . . . . . . .544port-profile (port-profile-

122 Network OS Command Reference53-1003115-01clear ip ospf2clear ip ospf Clears OSPF process, counters, neighbors, or routes.Synopsis clear ip ospf al

Network OS Command Reference 12353-1003115-01clear ip ospf2A.B.C.D Specifies the IP address of the neighbor to clear.all Clears all neighbors.routes C

124 Network OS Command Reference53-1003115-01clear ip pim mcache2clear ip pim mcacheClears the Protocol Independent Multicast forwarding cache.Synopsi

Network OS Command Reference 12553-1003115-01clear ip pim rp-map2clear ip pim rp-mapClears the static multicast forwarding table.Synopsis clear ip pim

126 Network OS Command Reference53-1003115-01clear ip pim traffic2clear ip pim trafficClears the Protocol Independent Multicast (PIM) traffic counters

Network OS Command Reference 12753-1003115-01clear ip route2clear ip routeClears IP routes. Synopsis clear ip route {A.B.C.D/M | all | slot line_card_

128 Network OS Command Reference53-1003115-01clear lacp2clear lacpClears the Link Aggregation Group Control Protocol (LACP) counters on a specific por

Network OS Command Reference 12953-1003115-01clear lacp counters2clear lacp countersClears the Link Aggregation Group Control Protocol (LACP) counters

130 Network OS Command Reference53-1003115-01clear lldp neighbors2clear lldp neighborsClears the Link Layer Discovery Protocol (LLDP) neighbor informa

Network OS Command Reference 13153-1003115-01clear lldp statistics2clear lldp statisticsClears LLDP statistics for all interfaces or a specified inter

Network OS Command Reference xvii53-1003115-01qos rcv-queue cos-threshold. . . . . . . . . . . . . . . . . . . . . . . . . . .594qos rcv-queue multica

132 Network OS Command Reference53-1003115-01clear logging auditlog2clear logging auditlog Clears the audit log system messages.Synopsis clear logging

Network OS Command Reference 13353-1003115-01clear logging raslog2clear logging raslogClears RASLog messages from the switch.Synopsis clear logging ra

134 Network OS Command Reference53-1003115-01clear mac-address-table dynamic2clear mac-address-table dynamicProvides a mechanism for clearing the MAC

Network OS Command Reference 13553-1003115-01clear mac-address-table dynamic2Examples NoneSee Also None

136 Network OS Command Reference53-1003115-01clear nas statistics2clear nas statistics Clears automatic network attached storage (NAS) statistics.Syno

Network OS Command Reference 13753-1003115-01clear policy-map-counters2clear policy-map-counters Provides a mechanism for clearing the policy map coun

138 Network OS Command Reference53-1003115-01clear sessions2clear sessionsTo log out the user sessions connected to the switch.Synopsis clear sessions

Network OS Command Reference 13953-1003115-01clear sflow statistics2clear sflow statisticsClears all sFlow statistics.Synopsis clear sflow statistics

140 Network OS Command Reference53-1003115-01clear spanning-tree counter2clear spanning-tree counterClears all spanning-tree counters on the interface

Network OS Command Reference 14153-1003115-01clear spanning-tree detected-protocols2clear spanning-tree detected-protocolsClears all spanning-tree det

xviii Network OS Command Reference53-1003115-01seq (standard MAC ACLs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .651service password-e

142 Network OS Command Reference53-1003115-01clear support2clear supportRemoves support data on the switch.Synopsis clear support [rbridge-id {rbridge

Network OS Command Reference 14353-1003115-01clear udld statistics2clear udld statisticsClears UDLD statistics.Synopsis clear udld statistics [interfa

144 Network OS Command Reference53-1003115-01clear vrrp statistics2clear vrrp statisticsClears VRRP statistics.Synopsis clear vrrp statistics clear vr

Network OS Command Reference 14553-1003115-01clear vrrp statistics2switch# clear vrrp stastistics interface tengigabitethernet 121/0/50 To clear stati

146 Network OS Command Reference53-1003115-01client-to-client-reflection (BGP)2client-to-client-reflection (BGP)Enables routes from one client to be r

Network OS Command Reference 14753-1003115-01clock set2clock setSets the local clock date and time. Synopsis clock set CCYY-MM-DDTHH:MM:SS [rbridge-id

148 Network OS Command Reference53-1003115-01clock timezone2clock timezoneSets the time zone based on region and longitudinal city. Synopsis clock tim

Network OS Command Reference 14953-1003115-01clock timezone2To remove the timezone setting:switch# no clock timezone rbridge-id 5 See Also clock set,

150 Network OS Command Reference53-1003115-01cluster-id (BGP)2cluster-id (BGP)Configures a cluster ID for the route reflector.Synopsis cluster-id [num

Network OS Command Reference 15153-1003115-01compare-med-empty-aspath (BGP)2compare-med-empty-aspath (BGP)Enables comparison of Multi-Exit Discriminat

Network OS Command Reference xix53-1003115-01show cert-util sshkey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .700show cert-util

152 Network OS Command Reference53-1003115-01compare-routerid (BGP)2compare-routerid (BGP)Enables comparison of router IDs, so that the path-compariso

Network OS Command Reference 15353-1003115-01configure terminal2configure terminalEnters global configuration mode.Synopsis configure terminalOperands

154 Network OS Command Reference53-1003115-01conform-set-dscp2conform-set-dscpOptional command for configuring the packet DSCP priority of a class-map

Network OS Command Reference 15553-1003115-01conform-set-prec2conform-set-precOptional command for configuring the packet IP precedence value of a cla

156 Network OS Command Reference53-1003115-01conform-set-tc2conform-set-tc Optional command for configuring the CIR internal queue assignment of a cla

Network OS Command Reference 15753-1003115-01connector2connectorExecutes connector mode for the purpose of configuring breakout mode on Quad SFPs (QSF

158 Network OS Command Reference53-1003115-01continue2continueConfigures a route-map instance number that goes in a continue statement in a route-map

Network OS Command Reference 15953-1003115-01copy2copyCopies configuration data.Synopsis copy source_file destination_file Operands source_file The so

160 Network OS Command Reference53-1003115-01copy2usb://path A file on an attached USB device. Defaults NoneCommand Modes Privileged EXEC modeDescript

Network OS Command Reference 16153-1003115-01copy default-config startup-config2copy default-config startup-configRestores the startup configuration t

Copyright © 2013-2014 Brocade Communications Systems, Inc. All Rights Reserved.Brocade, the B-wing symbol, Brocade Assurance, ADX, AnyIO, DCX, Fabric

xx Network OS Command Reference53-1003115-01show environment temp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .755show fabric all . .

162 Network OS Command Reference53-1003115-01copy running-config startup-config2copy running-config startup-configCopies the running configuration to

Network OS Command Reference 16353-1003115-01copy snapshot (logical chassis cluster mode)2copy snapshot (logical chassis cluster mode)Uploads and down

164 Network OS Command Reference53-1003115-01copy support2copy supportCopies support data to a remote host or a USB device.Synopsis copy support {ftp

Network OS Command Reference 16553-1003115-01copy support2To copy support data to a subdirectory:switch# copy support support-param sub-directory M8 t

166 Network OS Command Reference53-1003115-01copy support-interactive2copy support-interactiveCopies support data interactively.Synopsis copy support-

Network OS Command Reference 16753-1003115-01cos-mutation2cos-mutationSpecifies the mutation-map to be used on the port. Synopsis cos-mutation map_nam

168 Network OS Command Reference53-1003115-01cos-traffic-class2cos-traffic-classSpecifies the CoStraffic class mutation map to be used on the port. Sy

Network OS Command Reference 16953-1003115-01counter reliability2counter reliabilitySets and displays the reliability counter for the Access Gateway N

170 Network OS Command Reference53-1003115-01dampening (BGP)2dampening (BGP)Sets dampening parameters for the route.Synopsis dampening {half-life reus

Network OS Command Reference 17153-1003115-01database-overflow-interval (OSPF)2database-overflow-interval (OSPF)Configures frequency for monitoring da

Network OS Command Reference xxi53-1003115-01show ip bgp neighbors routes-summary . . . . . . . . . . . . . . . . .840show ip bgp peer-group . . . .

172 Network OS Command Reference53-1003115-01debug access-list-log buffer2debug access-list-log bufferConfigures ACL buffer characteristics.Synopsis d

Network OS Command Reference 17353-1003115-01debug dhcp packet buffer2debug dhcp packet bufferConfigures a buffer to capture DHCP packets.Synopsis deb

174 Network OS Command Reference53-1003115-01debug dhcp packet buffer clear2debug dhcp packet buffer clearClears buffer content from DHCP packet captu

Network OS Command Reference 17553-1003115-01debug dhcp packet buffer interface2debug dhcp packet buffer interfaceEnables and disables DHCP packet cap

176 Network OS Command Reference53-1003115-01debug dhcp packet buffer interface2Use the no form of this command to disable the DHCP packet capture on

Network OS Command Reference 17753-1003115-01debug fcoe show swcfg2debug fcoe show swcfgDisplays information related to FCoE classified VLAN configura

178 Network OS Command Reference53-1003115-01debug ip2debug ipEnables debugging for the IGMP and ICMP traffic on the switch.Synopsis debug ip packet [

Network OS Command Reference 17953-1003115-01debug ip2Examples NoneSee Also None

180 Network OS Command Reference53-1003115-01debug ip bgp2debug ip bgpDisplays information related to the processing of BGP4, with a variety of option

Network OS Command Reference 18153-1003115-01debug ip bgp address-family ipv4 unicast2debug ip bgp address-family ipv4 unicastDisplays information rel

xxii Network OS Command Reference53-1003115-01show ipv6 route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .903show lacp .

182 Network OS Command Reference53-1003115-01debug ip bgp neighbor2debug ip bgp neighborDisplays information related to the processing of BGP4 for a s

Network OS Command Reference 18353-1003115-01debug ip igmp2debug ip igmp Enables debugging for IGMP information.Synopsis debug ip igmp {all | group A.

184 Network OS Command Reference53-1003115-01debug ip igmp2• On Brocade VDX 8770 switches: 1 through 4086 for 802.1Q VLANs (VLAN IDs 4087 through 4095

Network OS Command Reference 18553-1003115-01debug ip ospf2debug ip ospfEnables debugging for the IP Open Shortest Path First (OSPF) protocol.Synopsis

186 Network OS Command Reference53-1003115-01debug ip pim2debug ip pim Enables debugging for IP Protocol Independent Multicast.Synopsis debug ip pim {

Network OS Command Reference 18753-1003115-01debug ip rtm2debug ip rtmEnables debugging for IP RTM. Synopsis debug ip rtm {A.B.C.D | all | counters {c

188 Network OS Command Reference53-1003115-01debug ip rtm2total_number:128, allocated_number:1, alloc_failure 0flag: 0, pool_index:1, avail_data:10221

Network OS Command Reference 18953-1003115-01debug ip vrf2debug ip vrfDisplays information related to VRF.Synopsis debug ip vrf ip-addrno debug ip vrf

190 Network OS Command Reference53-1003115-01debug lacp2debug lacpEnables debugging for the Link Aggregation Control Protocol (LACP).Synopsis debug la

Network OS Command Reference 19153-1003115-01debug lacp2port Specifies a valid port number.interface gigabitethernet rbridge-id/slot/port Specifies a

Network OS Command Reference xxiii53-1003115-01show process memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .961show prom-access .

192 Network OS Command Reference53-1003115-01debug lldp dump2debug lldp dumpDumps the LLDP debug information to the console.Synopsis debug lldp dump {

Network OS Command Reference 19353-1003115-01debug lldp dump2Sending TLVs: CHASSIS_ID: 0x00051ecd226a (MAC) PORT_ID: Te 1/0/3 (IF Name) TTL:

194 Network OS Command Reference53-1003115-01debug lldp packet2debug lldp packetEnables debugging for the Link Layer Discovery Protocol (LLDP).Synopsi

Network OS Command Reference 19553-1003115-01debug lldp packet2Examples To enable debugging of LLDP for both received and transmitted packets on the 1

196 Network OS Command Reference53-1003115-01debug lldp dump2debug lldp dumpDumps the Link Layer Discovery Protocol (LLDP) data to the console.Synopsi

Network OS Command Reference 19753-1003115-01debug spanning-tree2debug spanning-treeEnables debugging for the Spanning Tree Protocol (STP).Synopsis de

198 Network OS Command Reference53-1003115-01debug spanning-tree2Te 0/1 rx is onSpanning-tree tx debugging is offTe 0/1 tx is onSee Also show debug sp

Network OS Command Reference 19953-1003115-01debug udld2debug udldEnables debugging for the UniDirectional Link Detection (UDLD) protocol.Synopsis deb

200 Network OS Command Reference53-1003115-01debug vrrp2debug vrrpEnables debugging for the Virtual Router Redundancy Protocol (VRRP).Synopsis debug v

Network OS Command Reference 20153-1003115-01debug vrrp2port Specifies a valid port number.ve vlan_id Specifies the VLAN number for a virtual Ethernet

xxiv Network OS Command Reference53-1003115-01show running-config interfacefortygigabitethernet description . . . . . . . . . . . . . . . . . . . . .

202 Network OS Command Reference53-1003115-01default-information-originate (BGP)2default-information-originate (BGP)Configures the device to originate

Network OS Command Reference 20353-1003115-01default-information-originate (OSPF)2default-information-originate (OSPF)Controls distribution of default

204 Network OS Command Reference53-1003115-01default-local-preference (BGP)2default-local-preference (BGP)Enables setting of a local preference value

Network OS Command Reference 20553-1003115-01default-metric (BGP)2default-metric (BGP)Changes the default metric used for redistribution.Synopsis defa

206 Network OS Command Reference53-1003115-01default-metric (OSPF)2default-metric (OSPF)Sets the default metric value for the OSPF routing protocol.Sy

Network OS Command Reference 20753-1003115-01default-passive-interface (OSPF)2default-passive-interface (OSPF)Marks all OSPF interfaces passive by def

208 Network OS Command Reference53-1003115-01delete2deleteDeletes a file from the flash memory.Synopsis delete file Operands file The name of the file

Network OS Command Reference 20953-1003115-01deny (extended ACLs)2deny (extended ACLs)Configures a MAC address rule to drop traffic based on the sourc

210 Network OS Command Reference53-1003115-01deny (extended ACLs)2• The order of the rules in an ACL is critical. The first rule that matches the traf

Network OS Command Reference 21153-1003115-01deny (standard ACLs)2deny (standard ACLs) Configures a MAC address rule to drop traffic based on the sour

Network OS Command Reference xxv53-1003115-01show running-config interfacetengigabitethernet bpdu-drop . . . . . . . . . . . . . . . . . . . . . . . .

212 Network OS Command Reference53-1003115-01description (interfaces)2description (interfaces)Describes the interface.Synopsis description line no des

Network OS Command Reference 21353-1003115-01description (LLDP)2description (LLDP)Specifies a string that contains the LLDP description.Synopsis descr

214 Network OS Command Reference53-1003115-01description (Port Mirroring)2description (Port Mirroring)Specifies a string that contains the description

Network OS Command Reference 21553-1003115-01description (VRRP)2description (VRRP)Describes a VRRP-E interface.Synopsis description description no des

216 Network OS Command Reference53-1003115-01desire-distance2desire-distanceSets the desired distance attribute for a Fibre Channel port used in the D

Network OS Command Reference 21753-1003115-01dhcp auto-deployment enable2dhcp auto-deployment enableEnables DHCP auto-deployment on the switch.Synopsi

218 Network OS Command Reference53-1003115-01diag burninerrclear2diag burninerrclearClears the error logs that are stored in the nonvolatile memory. T

Network OS Command Reference 21953-1003115-01diag clearerror2diag clearerrorClears the diagnostic errors encountered during offline diagnostic tests.

220 Network OS Command Reference53-1003115-01diag portledtest2diag portledtestRuns various action modes on the port LED tests and validates the functi

Network OS Command Reference 22153-1003115-01diag portledtest2The rbridge-id is an optional parameter. If the rbridge-id is not specified, the test is

xxvi Network OS Command Reference53-1003115-01show running-config port-profile . . . . . . . . . . . . . . . . . . . . . . 1098show running-config po

222 Network OS Command Reference53-1003115-01diag portloopbacktest2diag portloopbacktestRuns the port loopback test on a given slot-based switch or fi

Network OS Command Reference 22353-1003115-01diag portloopbacktest2Usage Guidelines During abnormal termination, the system might be in unusable state

224 Network OS Command Reference53-1003115-01diag post enable2diag post enableEnables and disables the power-on self-test (POST). Synopsis diag post [

Network OS Command Reference 22553-1003115-01diag prbstest2diag prbstestRuns the Pseudo Random Bit Sequence (PRBS) test on a given slot to verify the

226 Network OS Command Reference53-1003115-01diag setcycle2diag setcycleConfigures all the parameters required for the system verification test.Synops

Network OS Command Reference 22753-1003115-01diag setcycle2DEFAULT - KEYWORD : COMMENT 1 - number_of_runs : number of passes of verify (0=infinite)

228 Network OS Command Reference53-1003115-01diag systemverification2diag systemverificationRuns a combination of various hardware diagnostic tests ba

Network OS Command Reference 22953-1003115-01diag turboramtest2diag turboramtestThis test performs a series of low-level structural tests to determine

230 Network OS Command Reference53-1003115-01dir2dirLists the contents of the switch flash memory.Synopsis dir Operands NoneDefaults NoneCommand Modes

Network OS Command Reference 23153-1003115-01distance (BGP)2distance (BGP)Changes the default administrative distances for EBGP, IBGP, and local BGP4.

Network OS Command Reference xxvii53-1003115-01show running-config username. . . . . . . . . . . . . . . . . . . . . . . .1147show running-config vcs

232 Network OS Command Reference53-1003115-01distance (OSPF)2distance (OSPF)Configures an administrative distance value for OSPF routes.Synopsis dista

Network OS Command Reference 23353-1003115-01distribute-list route-map (OSPF)2distribute-list route-map (OSPF)Creates a route-map distribution list.Sy

234 Network OS Command Reference53-1003115-01dot1x authentication2dot1x authenticationEnables 802.1Xauthentication on a port.Synopsis dot1x authentica

Network OS Command Reference 23553-1003115-01dot1x enable2dot1x enableEnables 802.1X authentication globally. Synopsis dot1x enable no dot1x enable Op

236 Network OS Command Reference53-1003115-01dot1x port-control2dot1x port-controlControls port-state authorization. Synopsis dot1x port-control {auto

Network OS Command Reference 23753-1003115-01dot1x quiet-period2dot1x quiet-periodSets the number of seconds that a switch remains quiet between a fai

238 Network OS Command Reference53-1003115-01dot1x reauthenticate interface2dot1x reauthenticate interfaceInitiates 802.1X reauthentication on a speci

Network OS Command Reference 23953-1003115-01dot1x reauthentication2dot1x reauthenticationEnables 802.1X port reauthentication.Synopsis dot1x reauthen

240 Network OS Command Reference53-1003115-01dot1x reauthMax2dot1x reauthMaxSets the maximum number of times that a port attempts 802.1Xreauthenticati

Network OS Command Reference 24153-1003115-01dot1x test eapol-capable2dot1x test eapol-capable Executes the 802.1x readiness check on the switch. Syno

xxviii Network OS Command Reference53-1003115-01show vlan classifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1207show vlan pr

242 Network OS Command Reference53-1003115-01dot1x test timeout2dot1x test timeout Sets the 802.1X readiness test timeout.Synopsis dot1x test timeout

Network OS Command Reference 24353-1003115-01dot1x timeout re-authperiod2dot1x timeout re-authperiodSets the 802.1X reauthorization-attempts interval.

244 Network OS Command Reference53-1003115-01dot1x timeout server-timeout2dot1x timeout server-timeoutSets the 802.1X authentication-sever response ti

Network OS Command Reference 24553-1003115-01dot1x timeout supp-timeout2dot1x timeout supp-timeoutSpecifies the EAP response timeout for 802.1X authen

246 Network OS Command Reference53-1003115-01dot1x timeout tx-period2dot1x timeout tx-period Sets the time the switch waits for a response to an Exten

Network OS Command Reference 24753-1003115-01dpod2dpodManages Dynamic Ports on Demand (POD) assignments.Synopsis dpod rbridge-id/slot/port {reserve |

248 Network OS Command Reference53-1003115-01dscp-cos2dscp-cos Specifies a user-defined mutation-map to be used on the port. Synopsis dscp-cos map_nam

Network OS Command Reference 24953-1003115-01dscp-mutation2dscp-mutation Specifies the dscp-mutation mutation-map to be used on the port. Synopsis dsc

250 Network OS Command Reference53-1003115-01dscp-traffic-class2dscp-traffic-classSpecifies the traffic-class mutation-map to be used on the port. Syn

Network OS Command Reference 25153-1003115-01ebs2ebs Optional command for configuring the excess burst size of a class-map.Synopsis ebs ebs-sizeno ebs

Network OS Command Reference xxix53-1003115-01ssh server shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1260ssh server status

252 Network OS Command Reference53-1003115-01eir2eir Optional command for configuring the excess information rate for a class-map.Synopsis eir eir-rat

Network OS Command Reference 25353-1003115-01hello-interval (ELD)2hello-interval (ELD)This global level configuration defines the interval for sending

254 Network OS Command Reference53-1003115-01edge-loop-detection port-priority2edge-loop-detection port-prioritySets the ELD priority for a port.Synop

Network OS Command Reference 25553-1003115-01edge-loop-detection vlan2edge-loop-detection vlanEnables edge-loop detection (ELD) on a port and VLAN.Syn

256 Network OS Command Reference53-1003115-01end2end Returns to the Privileged EXEC command mode from all configuration modes.Synopsis end Operands No

Network OS Command Reference 25753-1003115-01enable2enable Enables a VRRP-E session.Synopsis enableno enableOperands NoneDefaults NoneCommand Modes Vi

258 Network OS Command Reference53-1003115-01enforce-first-as (BGP)2enforce-first-as (BGP)Enforces the use of the first autonomous system (AS) path fo

Network OS Command Reference 25953-1003115-01enodes-config2enodes-configConfigures the number of FCoE interfaces to be created on FCoE nodes (ENodes).

260 Network OS Command Reference53-1003115-01error-disable-timeout enable2error-disable-timeout enableEnables the timer to bring the interface out of

Network OS Command Reference 26153-1003115-01error-disable-timeout interval2error-disable-timeout interval Sets the timeout for errors on an interface

Network OS Command Reference iii53-1003115-01

xxx Network OS Command Reference53-1003115-01threshold-monitor sfp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1318timeout fnm . . .

262 Network OS Command Reference53-1003115-01exceed-set-dscp2exceed-set-dscpOptional command for configuring the CIR packet IP precedence of a class-m

Network OS Command Reference 26353-1003115-01exceed-set-prec2exceed-set-precOptional command for configuring the CIR packet IP precedence of a class-m

264 Network OS Command Reference53-1003115-01exceed-set-tc2exceed-set-tcOptional command for configuring the queue assignment of the trafficclass vari

Network OS Command Reference 26553-1003115-01exit2exit Exits the current mode and returns to the previous mode.Synopsis exit Operands NoneDefaults Non

266 Network OS Command Reference53-1003115-01external-lsdb-limit (OSPF)2external-lsdb-limit (OSPF)Configures the maximum size of the external link sta

Network OS Command Reference 26753-1003115-01fabric ecmp load-balance2fabric ecmp load-balance Configures the hashing fields.Synopsis fabric ecmp load

268 Network OS Command Reference53-1003115-01fabric ecmp load-balance-hash-swap2fabric ecmp load-balance-hash-swap Configures how to swap the input fi

Network OS Command Reference 26953-1003115-01fabric isl enable2fabric isl enableEnables and disables the administration and operational state of an In

270 Network OS Command Reference53-1003115-01fabric route mcast2fabric route mcastSets the multicast priority for the local RBridge in the fabric. Syn

Network OS Command Reference 27153-1003115-01fabric trunk enable2fabric trunk enableEnables and disables trunking on a port.Synopsis fabric trunk enab

Network OS Command Reference xxxi53-1003115-01zoning defined-configuration alias . . . . . . . . . . . . . . . . . . . . 1369zoning defined-configura

272 Network OS Command Reference53-1003115-01fabric vlag2fabric vlag Configures the load balancing feature on a remote RBridge.Synopsis fabric vlag po

Network OS Command Reference 27353-1003115-01fabric-map2fabric-mapEnables FCoE fabric-map configuration mode.Synopsis fabric-map default Operands None

274 Network OS Command Reference53-1003115-01fast-external-failover (BGP)2fast-external-failover (BGP)Resets the session if a link to an EBGP peer goe

Network OS Command Reference 27553-1003115-01fastboot2fastbootReboots the control processor (CP), bypassing the power-on self-tests (POST).Synopsis fa

276 Network OS Command Reference53-1003115-01fcmap2fcmap Configures the FCMAP for an FCoE fabric-map. Synopsis fcmap hh:hh:hh Operands hh:hh:hh A vali

Network OS Command Reference 27753-1003115-01fcoe2fcoeEnables the FCoE configuration mode.Synopsis fcoe Operands NoneDefaults NoneCommand Modes Global

278 Network OS Command Reference53-1003115-01fcoe-enodes2fcoe-enodesSets the number of FCoE ENodes that are to be created on a switch.Synopsis fcoe-en

Network OS Command Reference 27953-1003115-01fcoe-profile (AMPP)2fcoe-profile (AMPP) Activates the FCoE profile configuration mode for AMPP. Synopsis

280 Network OS Command Reference53-1003115-01fcoeport2fcoeportProvisions a port with the default FCoE map.Synopsis fcoeport map no fcoeport Operands m

Network OS Command Reference 28153-1003115-01fcsp auth2fcsp authConfigures the protocol specific parameters.Synopsis fcsp auth auth-type dh-chap group

xxxii Network OS Command Reference53-1003115-01

282 Network OS Command Reference53-1003115-01fcsp auth2Authentication policy configuration is not distributed across the cluster. The rbridge-id of th

Network OS Command Reference 28353-1003115-01fcsp auth-secret dhchap2fcsp auth-secret dhchapSets the shared secret for DH CHAP authentication.Synopsis

284 Network OS Command Reference53-1003115-01fill-word2fill-wordConfigures the link initialization and fill word primitives for an 8 Gbps Fibre Channe

Network OS Command Reference 28553-1003115-01filter-change-update-delay2filter-change-update-delaySets a delay to change the delay in the filter-chang

286 Network OS Command Reference53-1003115-01fips root disable2fips root disablePermanently disables root access to a switch for compliance with Feder

Network OS Command Reference 28753-1003115-01fips selftests2fips selftestsEnables Federal Information Processing Standards (FIPS) self tests which wil

288 Network OS Command Reference53-1003115-01fips zeroize2fips zeroizeRemoves all critical security parameters from a switch in readiness for complian

Network OS Command Reference 28953-1003115-01firmware activate2firmware activateActivates the firmware in the Local or remote nodes after installing t

290 Network OS Command Reference53-1003115-01firmware activate2See Also firmware download, firmware restore, show version, show firmwaredownloadstatus

Network OS Command Reference 29153-1003115-01firmware commit2firmware commitCommits a firmware upgrade.Synopsis firmware commit Operands NoneDefaults

Network OS Command Reference xxxiii53-1003115-01About This DocumentIn this chapter•How this document is organized . . . . . . . . . . . . . . . . . .

292 Network OS Command Reference53-1003115-01firmware download2firmware downloadDownloads the firmware on the local switch.Synopsis firmware download

Network OS Command Reference 29353-1003115-01firmware download2By default, firmware download downloads the firmware to the system, reboots the system,

294 Network OS Command Reference53-1003115-01firmware download2(output truncated)To download firmware to a local node:switch# firmware download protoc

Network OS Command Reference 29553-1003115-01firmware download ftp2firmware download ftpSpecifies FTP as the protocol used to perform a firmware downl

296 Network OS Command Reference53-1003115-01firmware download ftp2By default, firmware download downloads the firmware to the system, reboots the sys

Network OS Command Reference 29753-1003115-01firmware download interactive2firmware download interactiveAllows the user to select firmware download pa

298 Network OS Command Reference53-1003115-01firmware download logical-chassis2firmware download logical-chassisDownloads the firmware onto the switch

Network OS Command Reference 29953-1003115-01firmware download logical-chassis2To reboot switches in a specific order, which can be done from any node

300 Network OS Command Reference53-1003115-01firmware download scp2firmware download scpSpecifies SCP as the protocol used to perform a firmware downl

Network OS Command Reference 30153-1003115-01firmware download scp2The device components supported by this command have two partitions of nonvolatile

xxxiv Network OS Command Reference53-1003115-01The following hardware platforms are supported by this release of Network OS:• Brocade VDX 6710-54• Bro

302 Network OS Command Reference53-1003115-01firmware download sftp2firmware download sftpSpecifies SFTP as the protocol used to perform a firmware do

Network OS Command Reference 30353-1003115-01firmware download sftp2The device components supported by this command have two partitions of nonvolatile

304 Network OS Command Reference53-1003115-01firmware download usb2firmware download usbSpecifies USB as the protocol used to perform a firmware downl

Network OS Command Reference 30553-1003115-01firmware download usb2This command does not support pagination.If the firmware download is interrupted be

306 Network OS Command Reference53-1003115-01firmware install2firmware installInstalls new software but deletes all configuration in the system.CAUTIO

Network OS Command Reference 30753-1003115-01firmware install2Usage Guidelines • In a dual-MM system, after firmware install is completed on both MMs,

308 Network OS Command Reference53-1003115-01firmware recover2firmware recoverRecovers the previous firmware version on the switch nodes if a firmware

Network OS Command Reference 30953-1003115-01firmware restore2firmware restoreSwaps the partition and reboots the node. CAUTIONDo not use this command

310 Network OS Command Reference53-1003115-01firmware sync2firmware syncSynchronizes firmware to standby MM.Synopsis firmware syncOperands NoneDefault

Network OS Command Reference 31153-1003115-01forward-delay2forward-delaySpecifies the time an interface spends in each of the listening and learning s

Network OS Command Reference xxxv53-1003115-01Document conventionsThis section describes text formatting conventions and important notice formats used

312 Network OS Command Reference53-1003115-01ha chassisreboot2ha chassisrebootPerforms a reboot of the chassis.Synopsis ha chassisreboot Operands None

Network OS Command Reference 31353-1003115-01ha disable2ha disableDisables the High Availability feature.Synopsis ha disable Operands NoneDefaults HA

314 Network OS Command Reference53-1003115-01ha enable2ha enableEnables the High Availability feature.Synopsis ha enable Operands NoneDefaults HA is d

Network OS Command Reference 31553-1003115-01ha failover2ha failoverInitiates a failover from the active to the standby management module (MM). Synops

316 Network OS Command Reference53-1003115-01ha sync start2ha sync startThis command is used to enable the high availability (HA) state synchronizatio

Network OS Command Reference 31753-1003115-01ha sync stop2ha sync stopDisables high availability state synchronization on a switch. Synopsis ha sync s

318 Network OS Command Reference53-1003115-01hardware2hardwareEnters hardware configuration mode to enter connector and port-group configuration mode.

Network OS Command Reference 31953-1003115-01hello (LLDP)2hello (LLDP)Sets the Hello transmit interval.Synopsis hello seconds no hello Operands second

320 Network OS Command Reference53-1003115-01hello (UDLD)2hello (UDLD)Sets the hello transmit interval.Synopsis hello hundred_milliseconds no hello Op

Network OS Command Reference 32153-1003115-01hello-interval2hello-intervalSets the interval between PDU packets sent from the ELD-enabled edge ports o

xxxvi Network OS Command Reference53-1003115-01Nesting square brackets and curly bracketsWhen reading a command entry, optional keywords are surrounde

322 Network OS Command Reference53-1003115-01hello-time2hello-timeSets the interval between the hello Bridge Protocol Data Units (BPDUs) sent on an in

Network OS Command Reference 32353-1003115-01hello-timer2hello-timerConfigures the Hello message periodic interval.Synopsis hello-timer num no hello-t

324 Network OS Command Reference53-1003115-01hold-time2hold-timeSets the time that a previously down backup VRRP router, which also must have a higher

Network OS Command Reference 32553-1003115-01inactivity-timer2inactivity-timer Configures the forwarding entry inactivity timer.Synopsis inactivity-ti

326 Network OS Command Reference53-1003115-01install-igp-cost (BGP)2install-igp-cost (BGP)Configures the device to use the IGP cost instead of the def

Network OS Command Reference 32753-1003115-01instance2instance Maps a VLAN to a Multiple Spanning Tree Protocol (MSTP) instance.Synopsis instance inst

328 Network OS Command Reference53-1003115-01interface2interface Enters the interface configuration mode to configure an interface.Synopsis interface

Network OS Command Reference 32953-1003115-01interface2Defaults NoneCommand Modes Global configuration modeDescription Use this command to create or e

330 Network OS Command Reference53-1003115-01interface (range specification)2interface (range specification)Allows a range of values to be entered for

Network OS Command Reference 33153-1003115-01interface (range specification)2vlan vlan_id Specifies the VLAN number. (Refer to the Usage Guidelines.)

Network OS Command Reference xxxvii53-1003115-01For definitions of SAN-specific terms, visit the Storage Networking Industry Association online dictio

332 Network OS Command Reference53-1003115-01interface (range specification)2• Ranges can be applied only to interfaces that belong to the same RBridg

Network OS Command Reference 33353-1003115-01interface loopback2interface loopbackConfigures a loopback interface. Synopsis interface loopback port_nu

334 Network OS Command Reference53-1003115-01interface management2interface managementEnters configuration mode for the management interface. Also use

Network OS Command Reference 33553-1003115-01interface management2ExamplesTo configure a management interface with an IPv6 IP address:switch(config)#

336 Network OS Command Reference53-1003115-01interface ve2interface veConfigures a virtual Ethernet (VE) interface.Synopsis interface ve vlan_id no in

Network OS Command Reference 33753-1003115-01interface vlan2interface vlan Allows the user to create 802.1Q VLANs, as well as service or transport VFs

338 Network OS Command Reference53-1003115-01interface vlan2See Also interface, interface ve, fcmap, shutdown (STP), switchport, vcs virtual-fabric en

Network OS Command Reference 33953-1003115-01ip access-group2ip access-groupApplies rules specified in a MAC ACL to traffic entering an interface.Syno

340 Network OS Command Reference53-1003115-01ip access-list2ip access-listCreates a standard or extended access control list (ACL) and, once created,

Network OS Command Reference 34153-1003115-01ip access-list2To create rules on a standard ACL:switch(config)# ip access-list standard stdACL3 switch(c

xxxviii Network OS Command Reference53-1003115-01Getting technical helpContact your switch support supplier for hardware, firmware, and software suppo

342 Network OS Command Reference53-1003115-01ip address2ip address Configures an IP address.Synopsis ip address ip-address/mask [secondary] [{ospf-ign

Network OS Command Reference 34353-1003115-01ip arp-aging-timeout2ip arp-aging-timeoutSets how long an ARP entry stays in cache.Synopsis ip arp-aging-

344 Network OS Command Reference53-1003115-01ip as-path access-list2ip as-path access-listConfigures an AS-path access control list (ACL). Synopsis ip

Network OS Command Reference 34553-1003115-01ip community-list extended2ip community-list extendedConfigures a community access control list (ACL), an

346 Network OS Command Reference53-1003115-01ip community-list standard2ip community-list standardConfigures a community access control list (ACL), an

Network OS Command Reference 34753-1003115-01ip dhcp relay address2ip dhcp relay addressConfigures the IP DHCP Relay on a Layer 3 interface.Synopsis i

348 Network OS Command Reference53-1003115-01ip directed-broadcast2ip directed-broadcastEnables IP directed broadcasts on an interface.Synopsis ip dir

Network OS Command Reference 34953-1003115-01ip dns2ip dns Sets the domain name service (DNS) parameters. Synopsis ip dns {domain-name domain_name |na

350 Network OS Command Reference53-1003115-01ip echo-reply2ip echo-replyEnables the generation of an Internet Control Message Protocol (ICMP) Echo Rep

Network OS Command Reference 35153-1003115-01ipv6 echo-reply2ipv6 echo-replyEnables the generation of an ICMPv6 Echo Reply message.Synopsis ipv6 echo-

Network OS Command Reference 153-1003115-01Chapter1Using the Network OS CLIIn this chapter•DCB command line interface . . . . . . . . . . . . . . . .

352 Network OS Command Reference53-1003115-01ip http-server enable2ip http-server enableEnables the HTTP server.Synopsis ip http-server enableno ip ht

Network OS Command Reference 35353-1003115-01ip icmp rate-limit2ip icmp rate-limit Limits the rate at which Internet Control Message Protool (ICMP) me

354 Network OS Command Reference53-1003115-01ipv6 icmp rate-limit2ipv6 icmp rate-limit Limits the rate at which ICMP messages are sent on a IPv6 netwo

Network OS Command Reference 35553-1003115-01ip igmp immediate-leave2ip igmp immediate-leaveRemoves a group from the IGMP table immediately when recei

356 Network OS Command Reference53-1003115-01ip igmp last-member-query-interval2ip igmp last-member-query-intervalSets the last member query interval.

Network OS Command Reference 35753-1003115-01ip igmp query-interval2ip igmp query-intervalSets the query interval.Synopsis ip igmp query-interval seco

358 Network OS Command Reference53-1003115-01ip igmp query-max-response-time2ip igmp query-max-response-timeSets the maximum response time for IGMP qu

Network OS Command Reference 35953-1003115-01ip igmp snooping enable (global version)2ip igmp snooping enable (global version)Enables Internet Group M

360 Network OS Command Reference53-1003115-01ip igmp snooping enable2ip igmp snooping enableEnables Internet Group Management Protocol (IGMP) snooping

Network OS Command Reference 36153-1003115-01ip igmp snooping fast-leave2ip igmp snooping fast-leaveEnables snooping fast-leave.Synopsis ip igmp snoop

iv Network OS Command Reference53-1003115-01

2 Network OS Command Reference53-1003115-01Network OS CLI RBAC permissions1Network OS CLI RBAC permissions Role-Based Action Control (RBAC) defines th

362 Network OS Command Reference53-1003115-01ip igmp snooping mrouter2ip igmp snooping mrouter Configures a VLAN port member to be a multicast router

Network OS Command Reference 36353-1003115-01ip igmp snooping mrouter2• On Brocade VDX 8770 switches: 1 through 4086 for 802.1Q VLANs (VLAN IDs 4087 t

364 Network OS Command Reference53-1003115-01ip igmp snooping mrouter-timeout2ip igmp snooping mrouter-timeout Configures the mrouter timeout value fo

Network OS Command Reference 36553-1003115-01ip igmp snooping querier enable2ip igmp snooping querier enableActivates or deactivates the Internet Grou

366 Network OS Command Reference53-1003115-01ip igmp static-group2ip igmp static-group Configures the static group membership entries for a specific i

Network OS Command Reference 36753-1003115-01ip load-sharing2ip load-sharingEnables load sharing. Synopsis ip load-sharing paths no ip load-sharing Op

368 Network OS Command Reference53-1003115-01ip mtu2ip mtu Sets the MTU. Synopsis ip mtu size no ip mtu Operands size Specifies the size of the maximu

Network OS Command Reference 36953-1003115-01ip multicast-boundary2ip multicast-boundary Configures a multicast boundary on an interface.Synopsis ip m

370 Network OS Command Reference53-1003115-01ip ospf active2ip ospf activeSets a specific OSPF interface to active.Synopsis ip ospf activeOperands Non

Network OS Command Reference 37153-1003115-01ip ospf passive2ip ospf passiveSets a specific OSPF interface to passive.Synopsis ip ospf passiveOperands

Network OS Command Reference 353-1003115-01Network OS CLI command modes1Network OS CLI command modesThe following lists the major Network OS CLI comma

372 Network OS Command Reference53-1003115-01ip ospf area2ip ospf areaEnables OSPF on an interface.Synopsis ip ospf area area-id no ip ospf area Opera

Network OS Command Reference 37353-1003115-01ip ospf auth-change-wait-time2ip ospf auth-change-wait-timeConfigures authentication-change hold time.Syn

374 Network OS Command Reference53-1003115-01ip ospf authentication-key2ip ospf authentication-keyConfigures simple password-based authentication for

Network OS Command Reference 37553-1003115-01ip ospf cost2ip ospf costConfigures cost for a specific interface.Synopsis ip ospf cost value no ip ospf

376 Network OS Command Reference53-1003115-01ip ospf database-filter2ip ospf database-filterConfigures filters for different types of outgoing Link St

Network OS Command Reference 37753-1003115-01ip ospf database-filter2See Also interface, interface ve, ip ospf area, ip ospf auth-change-wait-time, ip

378 Network OS Command Reference53-1003115-01ip ospf dead-interval2ip ospf dead-intervalConfigures neighbor dead interval.Synopsis ip ospf dead-interv

Network OS Command Reference 37953-1003115-01ip ospf hello-interval2ip ospf hello-intervalConfigures the hello interval.Synopsis ip ospf hello-interva

380 Network OS Command Reference53-1003115-01ip ospf md5-authentication2ip ospf md5-authenticationConfigures MD5 password and authentication change ho

Network OS Command Reference 38153-1003115-01ip ospf md5-authentication2Examples The following command sets authentication only on the OSPF 40-gigabit

4 Network OS Command Reference53-1003115-01Network OS CLI command modes1Protocol configurationLLDP:switch(conf-lldp)# Spanning-tree:switch(config-mstp

382 Network OS Command Reference53-1003115-01ip ospf mtu-ignore2ip ospf mtu-ignoreEnables or disables MTU-match checking.Synopsis ip ospf mtu-ignore n

Network OS Command Reference 38353-1003115-01ip ospf network2ip ospf networkConfigures network type.Synopsis ip ospf network {broadcast | point-to-poi

384 Network OS Command Reference53-1003115-01ip ospf passive2ip ospf passiveConfigures an interface as passive.Synopsis ip ospf passive no ip ospf pas

Network OS Command Reference 38553-1003115-01ip ospf priority2ip ospf priorityConfigures priority for designated router (DR) election. Synopsis ip osp

386 Network OS Command Reference53-1003115-01ip ospf retransmit-interval2ip ospf retransmit-intervalConfigures retransmit interval.Synopsis ip ospf re

Network OS Command Reference 38753-1003115-01ip ospf transmit-delay2ip ospf transmit-delayConfigures transmit delay for link-update packets.Synopsis i

388 Network OS Command Reference53-1003115-01ip pim dr-priority2ip pim dr-priority Configures the designated router (DR) priority of a PIM router.Syno

Network OS Command Reference 38953-1003115-01ip pim-sparse2ip pim-sparse Enables or disables Protocol Independent Multicast Sparse Mode on a physical

390 Network OS Command Reference53-1003115-01ip policy route-map2ip policy route-mapEnables policy-based routing (PBR) on any Layer 3 interface after

Network OS Command Reference 39153-1003115-01ip prefix-list2ip prefix-list Configures the IP prefix-list instance.Synopsis ip prefix-list name instanc

Network OS Command Reference 553-1003115-01Network OS CLI command modes1Routing protocol configurationBGP:switch(config)# switch(config-rbridge-id-1)#

392 Network OS Command Reference53-1003115-01ip proxy-arp2ip proxy-arpEnables proxy ARP on an interface.Synopsis ip proxy-arp no ip proxy-arp Operands

Network OS Command Reference 39353-1003115-01ip route2ip routeAdds a static route. Synopsis ip route A.B.C.D/L A.B.C.D [metric] [distance distance] [t

394 Network OS Command Reference53-1003115-01ip route2slot Specifies a valid slot number.port Specifies a valid port number.metric Cost metric of the

Network OS Command Reference 39553-1003115-01ip route next-hop ospf2ip route next-hop ospfEnables static-route next-hop-resolution with OSPF routes. S

396 Network OS Command Reference53-1003115-01ip route next-hop-enable-default2ip route next-hop-enable-defaultEnables the default route for next-hop r

Network OS Command Reference 39753-1003115-01ip route next-hop-recursion2ip route next-hop-recursionEnables Brocade switches to use routes to resolve

398 Network OS Command Reference53-1003115-01ip route next-hop-vrf2ip route next-hop-vrfEnables the leaking of static routes from one VRF instance to

Network OS Command Reference 39953-1003115-01ip router-id2ip router-idConfigures router ID. Synopsis ip router-id A.B.C.D no ip router-id A.B.C.D Oper

400 Network OS Command Reference53-1003115-01ip unreachable2ip unreachableProhibits routers from forwarding an Internet Control Message Protocol (ICMP

Network OS Command Reference 40153-1003115-01ipv6 echo-reply2ipv6 echo-replyEnables the generation of an Internet Control Message Protocol version 6 (

6 Network OS Command Reference53-1003115-01Network OS CLI command modes1Hardware configuration modeswitch(config)# hardware From global configuration

402 Network OS Command Reference53-1003115-01ipv6 icmp rate-limit2ipv6 icmp rate-limit Limits the rate at which Internet Control Message Protocol (ICM

Network OS Command Reference 40353-1003115-01ipv6 ra-guard2ipv6 ra-guardProtects against malicious Router Advertisements (RAs).Synopsis ipv6 ra-guard

404 Network OS Command Reference53-1003115-01ipv6 route2ipv6 routeConfigures a static IPv6 route.Synopsis ipv6 route IPv6_address/prefixno ipv6 route

Network OS Command Reference 40553-1003115-01ipv6 unreachable2ipv6 unreachableProhibits routers from forwarding an Internet Control Message Protocol v

406 Network OS Command Reference53-1003115-01iscsi-priority2iscsi-priority Sets the iSCSI priority bitmap.Synopsis iscsi-priority value no iscsi-prior

Network OS Command Reference 40753-1003115-01isl-r_rdy2isl-r_rdySets the flow control primitive used to prevent frame drop to ISL R_RDY mode.Synopsis

408 Network OS Command Reference53-1003115-01keep-alive timeout (fabric-map)2keep-alive timeout (fabric-map)Enables or disables the keep-alive timeout

Network OS Command Reference 40953-1003115-01l2traceroute2l2traceroute This command sends a simple traceroute from the source MAC address to the desti

410 Network OS Command Reference53-1003115-01l2traceroute2• IP Protocol Type [TCP |UDP|0–255]—Enter the IP protocol type including:• TCP (Transmission

Network OS Command Reference 41153-1003115-01lacp default-up2lacp default-upActivates an LACP link in the absence of PDUs.Synopsis lacp default-up no

Network OS Command Reference 753-1003115-01Network OS CLI command modes1NOTEPressing Ctrl+Z or entering the end command in any mode returns you to pri

412 Network OS Command Reference53-1003115-01lacp port-priority2lacp port-prioritySets port priority for an interface.Synopsis lacp port-priority valu

Network OS Command Reference 41353-1003115-01lacp system-priority2lacp system-prioritySets the Link Aggregation Control Protocol (LACP) system priorit

414 Network OS Command Reference53-1003115-01lacp timeout2lacp timeout Sets the timeout value used by the Link Aggregation Control Protocol (LACP) to

Network OS Command Reference 41553-1003115-01ldap-server host2ldap-server hostConfigures an LDAP-server host.Synopsis ldap-server host {ipaddr | FQDN}

416 Network OS Command Reference53-1003115-01ldap-server host2Executing no on an attribute sets it with its default value.switch(config)# no ldap-serv

Network OS Command Reference 41753-1003115-01ldap-server maprole2ldap-server maproleMaps an Active Directory (AD) group to a switch role.Synopsis ldap

418 Network OS Command Reference53-1003115-01license add2license addAdds a license key to a switch.Synopsis license add {licstr licenseString | FTP-UR

Network OS Command Reference 41953-1003115-01license remove2license removeRemoves a license key from a switch. Synopsis license remove licstr {license

420 Network OS Command Reference53-1003115-01line vty exec-timeout2line vty exec-timeoutSets the CLI session timeout.Synopsis line vty exec-timeout ti

Network OS Command Reference 42153-1003115-01linecard2linecardConfigures an interface module (line card).Synopsis linecard slot_number linecard_type n

8 Network OS Command Reference53-1003115-01Network OS CLI keyboard shortcuts1Network OS CLI keyboard shortcutsTable 1 lists Network OS CLI keyboard sh

422 Network OS Command Reference53-1003115-01linecard2LC72x1G 72X1G linecardswitch(config-rbridge-id-1)# linecard 1 LC48x10G Creating new linecard con

Network OS Command Reference 42353-1003115-01lldp dcbx-version2lldp dcbx-versionSpecifies which version of the Data Center Bridging Exchange (DCBX) pr

424 Network OS Command Reference53-1003115-01lldp disable2lldp disable Disables the Link Layer Discovery Protocol (LLDP).Synopsis lldp disable no lldp

Network OS Command Reference 42553-1003115-01lldp iscsi-priority2lldp iscsi-priority Sets the priority that will be advertised in the DCBX iSCSI TLV.S

426 Network OS Command Reference53-1003115-01lldp profile2lldp profile Applies a Link Layer Discovery Protocol (LLDP) profile to an interface.Synopsis

Network OS Command Reference 42753-1003115-01local-as (BGP)2local-as (BGP)Specifies the autonomous system number (ASN) where the device resides.Synops

428 Network OS Command Reference53-1003115-01log-dampening-debug (BGP)2log-dampening-debug (BGP)Logs dampening debug messages.Synopsis log-dampening-d

Network OS Command Reference 42953-1003115-01logging auditlog class2logging auditlog classSets the severity levels for the audit log class.Synopsis lo

430 Network OS Command Reference53-1003115-01logging raslog console2logging raslog consoleSets the severity levels for the RASLog console and allows u

Network OS Command Reference 43153-1003115-01logging syslog-facility local2logging syslog-facility localConfigures the syslog facility.Synopsis loggin

Network OS Command Reference 953-1003115-01Displaying Network OS CLI commands and command syntax1Displaying Network OS CLI commands and command syntax

432 Network OS Command Reference53-1003115-01logging syslog-server2logging syslog-serverConfigures a switch to forward system messages to specified se

Network OS Command Reference 43353-1003115-01logical-chassis principal-priority2logical-chassis principal-priority Sets the priority of a switch to as

434 Network OS Command Reference53-1003115-01logical-chassis principal-switchover2logical-chassis principal-switchover Triggers a fabric reformation a

Network OS Command Reference 43553-1003115-01long-distance2long-distanceConfigures a Fibre Channel port to support long distance.Synopsis long-distanc

436 Network OS Command Reference53-1003115-01long-distance2switch(config-FibreChannel-8/0/1)# desire-distance 100 switch(config-FibreChannel-8/0/1)# v

Network OS Command Reference 43753-1003115-01long-distance-isl2long-distance-islExtends an ISL link up to 30 km.Synopsis long-distance-isl {2000 | 500

438 Network OS Command Reference53-1003115-01long-distance-isl2The following displays the port groups and number of port groups available on each plat

Network OS Command Reference 43953-1003115-01mac2macAllows the user to add a MAC address to a MAC address group in a service or transport VF configura

440 Network OS Command Reference53-1003115-01mac access-group2mac access-groupApplies rules specified in a MAC access control list (ACL) to traffic en

Network OS Command Reference 44153-1003115-01mac access-list extended2mac access-list extended Creates and assigns a name to the extended MAC access l

10 Network OS Command Reference53-1003115-01Network OS CLI command completion1The Network OS CLI accepts abbreviations for commands. This example is t

442 Network OS Command Reference53-1003115-01mac access-list standard2mac access-list standard Creates and assigns a name to the standard MAC access l

Network OS Command Reference 44353-1003115-01mac-address-reduction2mac-address-reductionEnables or disables the MAC address reduction feature.Synopsis

444 Network OS Command Reference53-1003115-01mac-address-table2mac-address-table Sets the aging time or add static addresses to the MAC address table.

Network OS Command Reference 44553-1003115-01mac-address-table2• On Brocade VDX 8770 switches: 1 through 4086 for 802.1Q VLANs (VLAN IDs 4087 through

446 Network OS Command Reference53-1003115-01mac-group2mac-groupAllows the user to create a MAC address group into which one or more end-station MAC a

Network OS Command Reference 44753-1003115-01mac-rebalance2mac-rebalance Forces the rebalancing of EXM entries for the MAC tables.Synopsis mac-rebalan

448 Network OS Command Reference53-1003115-01management2managementEnables a variety of Dynamic Host Configuration Protocol (DHCP) management options.S

Network OS Command Reference 44953-1003115-01map2map Enables map configuration mode.Synopsis map {default} Operands default This keyword is required.

450 Network OS Command Reference53-1003115-01map fport interface fcoe2map fport interface fcoeMaps VF_Ports to N_Ports in Access Gateway (AG) mode and

Network OS Command Reference 45153-1003115-01map qos2map qosAdds the QoS profile name as an action to the policy map.Synopsis map qos profile_nameOper

Network OS Command Reference 1153-1003115-01Show command output information1Show command output informationNetwork OS contains many versions of the sh

452 Network OS Command Reference53-1003115-01map sflow2map sflowAdds the sFlow profile name as an action to the policy map.Synopsis map sflow profile_

Network OS Command Reference 45353-1003115-01match2matchCreates a classification map or “class-map” to classify traffic based on configured match crit

454 Network OS Command Reference53-1003115-01match (route map)2match (route map)Defines a variety of match conditions for a route map.Synopsis match {

Network OS Command Reference 45553-1003115-01match (route map)2level-1-2 Compares IS-IS routes with routes in the same and in different areas, but wit

456 Network OS Command Reference53-1003115-01match access-list2match access-listConfigures the access control list to be used with the class map.Synop

Network OS Command Reference 45753-1003115-01match as-path2match as-pathMatches an AS-path access list name in a route-map instance.Synopsis match as-

458 Network OS Command Reference53-1003115-01match community2match communityMatches a BGP community access list name in a route-map instance.Synopsis

Network OS Command Reference 45953-1003115-01match interface2match interfaceMatches interface conditions in a route-map instance.Synopsis match interf

460 Network OS Command Reference53-1003115-01match ip address2match ip addressMatches IP address conditions in a route-map instance.Synopsis match ip

Network OS Command Reference 46153-1003115-01match ip next-hop2match ip next-hopMatches IP next-hop match conditions in a route-map instance. Synopsis

Network OS Command Reference v53-1003115-01ContentsAbout This DocumentHow this document is organized . . . . . . . . . . . . . . . . . . . . . . . . .

12 Network OS Command Reference53-1003115-01Show command output information1

462 Network OS Command Reference53-1003115-01match metric2match metricMatches a route metric in a route-map instance.Synopsis match metric value no ma

Network OS Command Reference 46353-1003115-01match protocol bgp2match protocol bgpMatches BGP routes on protocol types and subtypes in a route-map ins

464 Network OS Command Reference53-1003115-01match route-type2match route-typeMatches a route type in a route-map instance.Synopsis match route-type [

Network OS Command Reference 46553-1003115-01match tag2match tagMatches a route tag in a route-map instance.Synopsis match tag value no match tagOpera

466 Network OS Command Reference53-1003115-01max-age2max-ageSets the interval time in seconds between messages that the spanning tree receives from th

Network OS Command Reference 46753-1003115-01max-hops2max-hopsConfigures the maximum number of hops for a Bridge Protocol Data Unit (BPDU) in an MSTP

468 Network OS Command Reference53-1003115-01max-mcache2max-mcache Configures the maximum multicast cache size.Synopsis max-mcache num no max-mcache O

Network OS Command Reference 46953-1003115-01max-metric router-lsa (OSPF)2max-metric router-lsa (OSPF)Advertises the maximum metric value in different

470 Network OS Command Reference53-1003115-01max-metric router-lsa (OSPF)2• Graceful removal of the router from the network for maintenance.• Graceful

Network OS Command Reference 47153-1003115-01max-route2max-routeSets the maximum number of routes for VRF.Synopsis max-route valueOperands value The m

Network OS Command Reference 1353-1003115-01Chapter2Network OS Commands aaa accounting Enables or disables the TACACS+ accounting service. Synopsis aa

472 Network OS Command Reference53-1003115-01maxas-limit (BGP)2maxas-limit (BGP)Imposes a limit on the number of autonomous systems in the AS-PATH att

Network OS Command Reference 47353-1003115-01maximum-paths (BGP)2maximum-paths (BGP)Changes the maximum number of BGP4 shared paths.Synopsis maximum-p

474 Network OS Command Reference53-1003115-01maximum-paths ebgp ibgp (BGP)2maximum-paths ebgp ibgp (BGP)Specifies the number of equal-cost multipath E

Network OS Command Reference 47553-1003115-01med-missing-as-worst (BGP)2med-missing-as-worst (BGP)Configures the device to favor a route that has a Mu

476 Network OS Command Reference53-1003115-01message-interval2message-interval Configures the Protocol Independent Multicast (PIM) Join/Prune message

Network OS Command Reference 47753-1003115-01metric-type (OSPF)2metric-type (OSPF)Configures the default metric type for external routes.Synopsis metr

478 Network OS Command Reference53-1003115-01minimum-links2minimum-links Sets the minimum bandwidth. Synopsis minimum-links num-of-links no minimum-li

Network OS Command Reference 47953-1003115-01mode2modeSets the LLDP mode on the switch.Synopsis mode {tx | rx}Operands tx Specifies to enable only th

480 Network OS Command Reference53-1003115-01modes2modesEnables and disables operating modes for port groups.Synopsis modes mode_nameno modes mode_nam

Network OS Command Reference 48153-1003115-01monitor session2monitor sessionEnables a Port Mirroring session for monitoring traffic.Synopsis monitor s

14 Network OS Command Reference53-1003115-01aaa accounting2Examples To enable command accounting: switch(config)# accounting command default start-sto

482 Network OS Command Reference53-1003115-01mtu2mtuSpecifies the size of the maximum transmission unit (MTU) on an interface.Synopsis mtu sizeOperand

Network OS Command Reference 48353-1003115-01multipath (BGP)2multipath (BGP)Changes load sharing to apply to only IBGP or EBGP paths, or to support lo

484 Network OS Command Reference53-1003115-01multiplier (LLDP)2multiplier (LLDP)Sets the number of consecutive misses of hello messages before LLDP de

Network OS Command Reference 48553-1003115-01multiplier (UDLD)2multiplier (UDLD)Sets timeout multiplier for missed UDLD PDUs.Synopsis multiplier value

486 Network OS Command Reference53-1003115-01nas auto-qos2nas auto-qosEnables the Quality of Service (QoS) functionality for the Auto-NAS (automatic n

Network OS Command Reference 48753-1003115-01nasport server-ip2nasport server-ip Identifies the port that is to receive Auto NAS (automatic network at

488 Network OS Command Reference53-1003115-01nbr-timeout2nbr-timeout Configures the neighbor timeout interval.Synopsis nbr-timeout num no nbr-timeout

Network OS Command Reference 48953-1003115-01neighbor (BGP)2neighbor (BGP)Assigns a neighbor to a specified IPv4 address or peer group to provide a va

490 Network OS Command Reference53-1003115-01neighbor (BGP)2Description Use this command to assign a neighbor to a specified peer group to provide a v

Network OS Command Reference 49153-1003115-01neighbor (OSPF)2neighbor (OSPF)Manually configures a neighbor.Synopsis neighbor A.B.C.D no neighbor Opera

Network OS Command Reference 1553-1003115-01aaa authentication2aaa authenticationConfigures the AAA login sequence.Synopsis aaa authentication login {

492 Network OS Command Reference53-1003115-01neighbor advertisement-interval (BGP)2neighbor advertisement-interval (BGP)Enables changes to interval ov

Network OS Command Reference 49353-1003115-01neighbor as-override (BGP)2neighbor as-override (BGP)Replaces the autonomous system number (ASN) of the o

494 Network OS Command Reference53-1003115-01neighbor capability as4 (BGP)2neighbor capability as4 (BGP)Enables or disables support for 4-byte auton

Network OS Command Reference 49553-1003115-01neighbor default-originate (BGP)2neighbor default-originate (BGP)Configures the device to send the defaul

496 Network OS Command Reference53-1003115-01neighbor description (BGP)2neighbor description (BGP)Specifies a name for a neighbor.Synopsis neighbor {i

Network OS Command Reference 49753-1003115-01neighbor ebgp-multihop (BGP)2neighbor ebgp-multihop (BGP)Allows EBGP neighbors that are not on directly c

498 Network OS Command Reference53-1003115-01neighbor enforce-first-as (BGP)2neighbor enforce-first-as (BGP)Ensures that a device requires the first A

Network OS Command Reference 49953-1003115-01neighbor filter-list (BGP)2neighbor filter-list (BGP)Specifies a filter list to be applied to updates fro

500 Network OS Command Reference53-1003115-01neighbor local-as (BGP)2neighbor local-as (BGP)Causes the device to prepend the local autonomous system n

Network OS Command Reference 50153-1003115-01neighbor maxas-limit in (BGP)2neighbor maxas-limit in (BGP)Causes the device to discard routes received i

16 Network OS Command Reference53-1003115-01aaa authentication2Usage Guidelines The authentication mode can only be set and cannot be added or deleted

502 Network OS Command Reference53-1003115-01neighbor maximum-prefix (BGP)2neighbor maximum-prefix (BGP)Specifies the maximum number of IP network pre

Network OS Command Reference 50353-1003115-01neighbor next-hop-self (BGP)2neighbor next-hop-self (BGP)Causes the device to list itself as the next hop

504 Network OS Command Reference53-1003115-01neighbor password (BGP)2neighbor password (BGP)Specifies an MD5 password for securing sessions between th

Network OS Command Reference 50553-1003115-01neighbor peer-group (BGP)2neighbor peer-group (BGP)Enables the creation of a BGP peer group.Synopsis neig

506 Network OS Command Reference53-1003115-01neighbor prefix-list (BGP)2neighbor prefix-list (BGP)Filters the outgoing and incoming route updates to o

Network OS Command Reference 50753-1003115-01neighbor remote-as (BGP)2neighbor remote-as (BGP)Specifies the autonomous system (AS) in which a remote n

508 Network OS Command Reference53-1003115-01neighbor remove-private-as (BGP)2neighbor remove-private-as (BGP)Configures a device to remove private au

Network OS Command Reference 50953-1003115-01neighbor route-map (BGP)2neighbor route-map (BGP)Filters the outgoing and incoming route updates to or fr

510 Network OS Command Reference53-1003115-01neighbor route-reflector-client (BGP)2neighbor route-reflector-client (BGP)Configures a neighbor to be a

Network OS Command Reference 51153-1003115-01neighbor send-community (BGP)2neighbor send-community (BGP)Enables sending the community attribute in upd

Network OS Command Reference 1753-1003115-01access-group2access-groupApplies or removes an ACL from an interface.Synopsis {ip | ipv6 | mac} access-gro

512 Network OS Command Reference53-1003115-01neighbor shutdown (BGP)2neighbor shutdown (BGP)Causes a device to shut down the session administratively

Network OS Command Reference 51353-1003115-01neighbor soft-reconfiguration inbound (BGP)2neighbor soft-reconfiguration inbound (BGP)Stores all the rou

514 Network OS Command Reference53-1003115-01neighbor timers (BGP)2neighbor timers (BGP)Specifies how frequently a device sends KEEPALIVE messages t

Network OS Command Reference 51553-1003115-01neighbor unsuppress-map (BGP)2neighbor unsuppress-map (BGP)Removes route suppression from neighbor routes

516 Network OS Command Reference53-1003115-01neighbor update-source (BGP)2neighbor update-source (BGP)Configures the device to communicate with a neig

Network OS Command Reference 51753-1003115-01neighbor update-source (BGP)2See Also None

518 Network OS Command Reference53-1003115-01neighbor weight (BGP)2neighbor weight (BGP)Specifies a weight that the device will add to routes that are

Network OS Command Reference 51953-1003115-01network (BGP)2network (BGP)Configures the device to advertise a network.Synopsis network network/mask [ro

520 Network OS Command Reference53-1003115-01next-hop-enable-default (BGP)2next-hop-enable-default (BGP)Configures the device to use the default route

Network OS Command Reference 52153-1003115-01next-hop-recursion (BGP)2next-hop-recursion (BGP)Enables recursive next-hop lookups.Synopsis next-hop-rec

18 Network OS Command Reference53-1003115-01access-list2access-listCreates an ACL.Synopsis {ip | ipv6 | mac} access-list {standard | extended} NAMEno

522 Network OS Command Reference53-1003115-01nport2nportEnables N_Port configuration mode for a specific N_Port ID for Access Gateway mode.Synopsis np

Network OS Command Reference 52353-1003115-01nport interface Fibrechannel2nport interface FibrechannelAdds or deletes N_Ports in a specified port grou

524 Network OS Command Reference53-1003115-01nssa-translator (OSPF)2nssa-translator (OSPF)Configures Not So Stubby Area (NSSA) Type 7-to-Type 5 Link S

Network OS Command Reference 52553-1003115-01ntp authentication-key2ntp authentication-keyCreates an authentication key to associate with the NTP serv

526 Network OS Command Reference53-1003115-01ntp server2ntp serverSpecifies or adds an NTP server IP address and associates an authentication key to t

Network OS Command Reference 52753-1003115-01oscmd2oscmdProvides a command shell for selected Linux commands.Synopsis oscmd Linux command Operands Lin

528 Network OS Command Reference53-1003115-01oscmd2Description Use this command to execute selected Linux commands on the switch. Usage Guidelines Ref

Network OS Command Reference 52953-1003115-01password-attributes2password-attributesConfigures the user password attributes.Synopsis password-attribut

530 Network OS Command Reference53-1003115-01password-attributes2password-attributes character-restriction special-char 1To reset the character restri

Network OS Command Reference 53153-1003115-01password-attributes admin-lockout enable2password-attributes admin-lockout enableEnables the lockout poli

Network OS Command Reference 1953-1003115-01address-family ipv4 unicast (BGP)2address-family ipv4 unicast (BGP)Enables IPv4 address-family support for

532 Network OS Command Reference53-1003115-01pdu-rx-limit2pdu-rx-limitSets the number of PDU packets received on an ELD-enabled port before detecting

Network OS Command Reference 53353-1003115-01permit (extended ACLs)2permit (extended ACLs) Configures a MAC address rule to permit traffic based on th

534 Network OS Command Reference53-1003115-01permit (extended ACLs)2To delete a filter rule in a MAC extended ACL:switch(conf-macl-ext)# no permit 002

Network OS Command Reference 53553-1003115-01permit (standard ACLs)2permit (standard ACLs)Configures a MAC address rule to permit traffic based on the

536 Network OS Command Reference53-1003115-01pg2pgCreates an N_Port group in Access Gateway mode.Synopsis pg pgidno pg pgidOperands pgid Port group id

Network OS Command Reference 53753-1003115-01ping2ping Verifies network connectivity between a source and a destination. Synopsis ping dest-IPv4_addr

538 Network OS Command Reference53-1003115-01ping25 packets transmitted, 5 packets received, 0% packet lossround-trip min/avg/max/stddev = 100.605/146

Network OS Command Reference 53953-1003115-01police cir2police cir Mandatory command for configuring the committed information rate for a class-map.Sy

540 Network OS Command Reference53-1003115-01police-priority-map2police-priority-map Creates color-based priority CoS mapping. A police-priority-map r

Network OS Command Reference 54153-1003115-01policy-map2policy-map Configures a policy-map containing a class-map so that you can apply Policer and Qo

20 Network OS Command Reference53-1003115-01address-family ipv4 unicast (VRF)2address-family ipv4 unicast (VRF)Enables IPv4 address-family support for

542 Network OS Command Reference53-1003115-01port-channel path-cost2port-channel path-costSets the path-cost behavior.Synopsis port-channel path-cost

Network OS Command Reference 54353-1003115-01port-group2port-group Enables port-group configuration mode for VDX 8770 Switch line cards that support t

544 Network OS Command Reference53-1003115-01port-profile (global configuration mode)2port-profile (global configuration mode)Creates a new Automatic

Network OS Command Reference 54553-1003115-01port-profile (port-profile-domain configuration mode)2port-profile (port-profile-domain configuration mod

546 Network OS Command Reference53-1003115-01port-profile-domain2port-profile-domainCreates an Automatic Migration of Port Profiles (AMPP) port-profil

Network OS Command Reference 54753-1003115-01port-profile-port2port-profile-portActivates the Automatic Migration of Port Profiles (AMPP) port-profile

548 Network OS Command Reference53-1003115-01port-profile-port2switch(conf-if-te-178/0/9)# port-profile-port domain vDC1To associate a profiled port w

Network OS Command Reference 54953-1003115-01port-shape2port-shapeSpecifies the shaping rate for a port.Synopsis port-shape speedOperands speed The sp

550 Network OS Command Reference53-1003115-01power-off2power-offDeactivates a line card or Switch Fabric Module (SFM).Synopsis power-off {linecard | s

Network OS Command Reference 55153-1003115-01power-off linecard2power-off linecardPowers off an interface module (line card).Synopsis power-off lineca

Network OS Command Reference 2153-1003115-01advertise dcbx-fcoe-app-tlv2advertise dcbx-fcoe-app-tlvAdvertises application Type, Length, Values (TLVs)

552 Network OS Command Reference53-1003115-01power-on2power-onActivates a line card or Switch Fabric Module (SFM). Synopsis power-on {linecard | sfm}

Network OS Command Reference 55353-1003115-01power-on linecard2power-on linecardPowers on an interface module (line card). Synopsis power-on linecard

554 Network OS Command Reference53-1003115-01precedence2precedence Sets the precedence of the CEE map.Synopsis precedence value Operands value The pre

Network OS Command Reference 55553-1003115-01preempt-mode2preempt-modeTurns on preempt mode for a VRRP router session.Synopsis preempt-mode no preempt

556 Network OS Command Reference53-1003115-01priority2prioritySets the priority of a physical router in a VRRP router group.Synopsis priority range Op

Network OS Command Reference 55753-1003115-01priority-group-table2priority-group-table Configures the bandwidth for each priority group.Synopsis prior

558 Network OS Command Reference53-1003115-01priority-group-table2switch(conf-ceemap)# priority-group-table 0 weight 50 pfc on switch(conf-ceemap)# pr

Network OS Command Reference 55953-1003115-01priority-tag2priority-tag Toggles priority-tagging support.Synopsis priority-tag no priority-tag Operands

560 Network OS Command Reference53-1003115-01private-vlan2private-vlanConfigures a VLAN as a private VLAN (PVLAN).Synopsis private-vlan [isolated | co

Network OS Command Reference 56153-1003115-01private-vlan association2private-vlan associationAssociates a secondary VLAN to a primary VLAN.Synopsis p

vi Network OS Command Reference53-1003115-01access-list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18address-

22 Network OS Command Reference53-1003115-01advertise dcbx-fcoe-logical-link-tlv2advertise dcbx-fcoe-logical-link-tlvAdvertises to any attached device

562 Network OS Command Reference53-1003115-01profile2profileCreates an LLDP profile.Synopsis profile name no profile name Operands name Assigns a nam

Network OS Command Reference 56353-1003115-01prom-access disable2prom-access disable Disables access to the Boot PROM for FIPS compliance.Synopsis pro

564 Network OS Command Reference53-1003115-01protect-mode enable2protect-mode enable Enables protect mode.Synopsis protect-mode enable no protect-mode

Network OS Command Reference 56553-1003115-01protocol edge-loop-detection2protocol edge-loop-detectionSets the edge-loop detection (ELD) configuration

566 Network OS Command Reference53-1003115-01protocol lldp2protocol lldp Enters the Link Layer Discovery Protocol (LLDP) configuration mode.Synopsis p

Network OS Command Reference 56753-1003115-01protocol spanning-tree2protocol spanning-tree Designates the context for spanning tree.Synopsis protocol

568 Network OS Command Reference53-1003115-01protocol udld2protocol udldEnables and/or enters unidirectional link detection (UDLD) protocol configurat

Network OS Command Reference 56953-1003115-01protocol vrrp2protocol vrrpGlobally enables VRRP (and VRRP-E on some platforms).Synopsis protocol vrrpno

570 Network OS Command Reference53-1003115-01protocol vrrp-extended2protocol vrrp-extendedGlobally enables VRRP-Extended.Synopsis protocol vrrp-extend

Network OS Command Reference 57153-1003115-01pwd2pwdPrint Working Directory displays the mode of the current working directory.Synopsis pwd Operands N

Network OS Command Reference 2353-1003115-01advertise dcbx-iscsi-app-tlv2advertise dcbx-iscsi-app-tlvAdvertises the iSCSI traffic configuration parame

572 Network OS Command Reference53-1003115-01qos cos2qos cos Specifies the interface Class of Service (CoS) value.Synopsis qos cos value no qos cos Op

Network OS Command Reference 57353-1003115-01qos cos-mutation2qos cos-mutationApplies a CoS-to-CoS mutation quality of Service (QoS) map on an interfa

574 Network OS Command Reference53-1003115-01qos cos-traffic-class2qos cos-traffic-class Applies a CoS-to-Traffic Class QoS map on an interface.Synops

Network OS Command Reference 57553-1003115-01qos dscp-cos2qos dscp-cos Applies a defined DSCP-CoS map to an interface, Synopsis qos dscp-cos name no q

576 Network OS Command Reference53-1003115-01qos dscp-mutation2qos dscp-mutation Applies a defined DSCP mutation map to an interface, Synopsis qos dsc

Network OS Command Reference 57753-1003115-01qos dscp-traffic-class2qos dscp-traffic-class Applies a defined DSCP-to-Traffic-Class map to an interface

578 Network OS Command Reference53-1003115-01qos flowcontrol tx2qos flowcontrol txActivates and configures QoS flow control. Synopsis qos flowcontrol

Network OS Command Reference 57953-1003115-01qos flowcontrol pfc2qos flowcontrol pfc Activates and configures flow control for a Class of Service (CoS

580 Network OS Command Reference53-1003115-01qos map cos-mutation2qos map cos-mutation Creates a QoS map for performing CoS-to-CoS mutation. Synopsis

Network OS Command Reference 58153-1003115-01qos map cos-traffic-class2qos map cos-traffic-class Creates a QoS map for performing CoS-to-Traffic Class

24 Network OS Command Reference53-1003115-01advertise dcbx-tlv2advertise dcbx-tlvAdvertises to any attached device mandatory Data Center Bridging eXch

582 Network OS Command Reference53-1003115-01qos map dscp-cos2qos map dscp-cosCreates a QoS map for performing DSCP-to-CoS mapping. This configures a

Network OS Command Reference 58353-1003115-01qos map dscp-mutation2qos map dscp-mutationCreates a DSCP mutation by remapping the incoming DSCP value o

584 Network OS Command Reference53-1003115-01qos map dscp-mutation2NOTEThis command is only supported on Brocade VDX 8770-4, VDX 8770-8, and later swi

Network OS Command Reference 58553-1003115-01qos map dscp-traffic-class2qos map dscp-traffic-class Creates a QoS map for performing DSCP-to-Traffic Cl

586 Network OS Command Reference53-1003115-01qos red profile2qos red profileCreates a Random Early Discard (RED) profile for egress traffic flow.Synop

Network OS Command Reference 58753-1003115-01qos trust cos2qos trust cosSpecifies the interface QoS trust Class of Service (CoS) mode for incoming tra

588 Network OS Command Reference53-1003115-01qos trust dscp2qos trust dscp Enables Differentiated Services Code Point (DSCP) mode for incoming traffic

Network OS Command Reference 58953-1003115-01qos queue multicast scheduler2qos queue multicast schedulerConfigures the multicast Traffic Class packet

590 Network OS Command Reference53-1003115-01qos queue multicast scheduler2Examples To set the multicast Traffic Class packet expansion scheduler for

Network OS Command Reference 59153-1003115-01qos queue scheduler2qos queue scheduler Configures the Traffic Class packet scheduler policy.Synopsis qos

Network OS Command Reference 2553-1003115-01advertise dot1-tlv2advertise dot1-tlvAdvertises to any attached device IEEE 802.1 organizationally specifi

592 Network OS Command Reference53-1003115-01qos queue scheduler2weight5 Sets the DWRR weight for Traffic Class 5 in units of bandwidth percentage lef

Network OS Command Reference 59353-1003115-01qos random-detect cos2qos random-detect cosMaps a Random Early Discard (RED) profile to a CoS priority va

594 Network OS Command Reference53-1003115-01qos rcv-queue cos-threshold2qos rcv-queue cos-threshold Configures the port tail drop thresholds.Synopsis

Network OS Command Reference 59553-1003115-01qos rcv-queue cos-threshold2Usage Guidelines The tail drop thresholds are not allowed to exceed 100%, but

596 Network OS Command Reference53-1003115-01qos rcv-queue multicast rate-limit2qos rcv-queue multicast rate-limitConfigures a cap on the maximum rate

Network OS Command Reference 59753-1003115-01qos rcv-queue multicast threshold2qos rcv-queue multicast thresholdConfigures a cap on the maximum queue

598 Network OS Command Reference53-1003115-01qos rcv-queue multicast threshold2Examples To increase multicast packet expansion Tail Drop Threshold to

Network OS Command Reference 59953-1003115-01qos-profile (AMPP)2qos-profile (AMPP) Activates the QoS profile mode for AMPP.Synopsis qos-profile no qos

600 Network OS Command Reference53-1003115-01radius-server2radius-serverConfigures the Remote Authentication Dial-In User Service (RADIUS) server.Syno

Network OS Command Reference 60153-1003115-01radius-server2Description Use this command to configure the attributes of the RADIUS server. If a RADIUS

26 Network OS Command Reference53-1003115-01advertise dot3-tlv2advertise dot3-tlvAdvertises to any attached device IEEE 802.3 organizationally specifi

602 Network OS Command Reference53-1003115-01rasman2rasmanProvides instant customer access to RASLog messages decoding and documentation on the switch

Network OS Command Reference 60353-1003115-01rasman2AUTH-1003 INFO %s type has been successfully set tAUTH-1004 ERROR Failed to set %s type to %s.AUTH

604 Network OS Command Reference53-1003115-01rasman2FCIP-1003 INFO An IPsec/IKE policy was deleted FCIP-1004 INFO Tape Read Pipelining is being disabl

Network OS Command Reference 60553-1003115-01rate-limit-delay get netconf2rate-limit-delay get netconfReturns the rate limit delay configured for proc

606 Network OS Command Reference53-1003115-01rate-limit-delay set netconf2rate-limit-delay set netconfLimits the rate at which BNA or NETCONF Remote P

Network OS Command Reference 60753-1003115-01rbridge-id2rbridge-idEnables RBridge ID configuration mode to support VCS on individual nodes.Synopsis rb

608 Network OS Command Reference53-1003115-01rbridge-id2 setting top Exit to top level and opt

Network OS Command Reference 60953-1003115-01rd (route distinguisher)2rd (route distinguisher)Distinguishes a route for VRF.Synopsis rd admin-value:ar

610 Network OS Command Reference53-1003115-01redistribute (BGP)2redistribute (BGP)Configures the device to redistribute OSPF, ISIS, or RIP routes, dir

Network OS Command Reference 61153-1003115-01redistribute (OSPF)2redistribute (OSPF)Configures the device to redistribute OSPF routes. Synopsis redist

Network OS Command Reference 2753-1003115-01advertise optional-tlv2advertise optional-tlvAdvertises the optional Type, Length, and Values (TLV) values

612 Network OS Command Reference53-1003115-01region2regionSpecifies the Multiple Spanning Tree Protocol (MSTP) region. Synopsis region region-name no

Network OS Command Reference 61353-1003115-01reload2reloadReboots the control processor (CP) or management module (MM).Synopsis reload [standby | syst

614 Network OS Command Reference53-1003115-01reload2The following summarizes the behavior of the reload command under a variety of conditions. NOTEMM

Network OS Command Reference 61553-1003115-01remap fabric-priority2remap fabric-priority Remaps the CoS fabric priority. Synopsis remap fabric-priorit

616 Network OS Command Reference53-1003115-01remap lossless-priority2remap lossless-priority Remaps the Brocade VCS Fabric priority. Synopsis remap lo

Network OS Command Reference 61753-1003115-01rename2renameRenames a file in the switch flash memory.Synopsis rename current_name new_name Operands cur

618 Network OS Command Reference53-1003115-01rename (Access Gateway mode)2rename (Access Gateway mode)Provides a name for a port group or renames a po

Network OS Command Reference 61953-1003115-01resequence access-list2resequence access-listSpecifies the renumbering of the rules in a MAC or IP ACL. S

620 Network OS Command Reference53-1003115-01reserved-vlan2reserved-vlanDefines the range of 802.1Q VLANs that cannot be created by means of the inter

Network OS Command Reference 62153-1003115-01restrict-flooding2restrict-floodingRestricts the flooding of egress BUM traffic from a port-profile port.

28 Network OS Command Reference53-1003115-01advertise-backup2advertise-backupEnables a backup VRRP router to send advertisement frames to the master V

622 Network OS Command Reference53-1003115-01revision2revisionAssigns a version number to the Multiple Spanning Tree Protocol (MSTP) configuration.Syn

Network OS Command Reference 62353-1003115-01rfc1583-compatibility (OSPF)2rfc1583-compatibility (OSPF)Configures compatibility with RFC 1583.Synopsis

624 Network OS Command Reference53-1003115-01rfc1587-compatibility (OSPF)2rfc1587-compatibility (OSPF)Configures compatibility with RFC 1587.Synopsis

Network OS Command Reference 62553-1003115-01rib-route-limit (BGP)2rib-route-limit (BGP)Limits the maximum number of BGP Routing Information Base (RIB

626 Network OS Command Reference53-1003115-01rmon alarm2rmon alarmSets the RMON alarm conditions. Synopsis rmon alarm index snmp_oid interval seconds

Network OS Command Reference 62753-1003115-01rmon collection history2rmon collection history Collects Ethernet group statistics for later retrieval. S

628 Network OS Command Reference53-1003115-01rmon collection stats2rmon collection stats Collects Ethernet group statistics.Synopsis rmon collection s

Network OS Command Reference 62953-1003115-01rmon event2rmon eventAdds or removes an event in the RMON event table associated to the RMON alarm number

630 Network OS Command Reference53-1003115-01role name2role nameCreates or modifies a user role.Synopsis role name role_name [desc description] no rol

Network OS Command Reference 63153-1003115-01route-map2route-map Creates or deletes a route map instance, with a variety of options.Synopsis route-map

Network OS Command Reference 2953-1003115-01advertisement interval (fabric-map)2advertisement interval (fabric-map)Configures the FIP advertisement in

632 Network OS Command Reference53-1003115-01route-map2• set community• set cos traffic-class• set dscp• set dampening• set distance• set ip next-hop•

Network OS Command Reference 63353-1003115-01router bgp2router bgpEnables BGP4 routing.Synopsis router bgpno router bgpOperands NoneDefaults NoneComma

634 Network OS Command Reference53-1003115-01router ospf2router ospf Enables and configures the Open Shortest Path First (OSPF) routing protocol over

Network OS Command Reference 63553-1003115-01router pim2router pim Enables or disables the Protocol Independent Multicast (PIM) routing protocol.Synop

636 Network OS Command Reference53-1003115-01route-target2route-targetImports or exports the routes for the router-id.Synopsis route-target [admin-val

Network OS Command Reference 63753-1003115-01rp-address2rp-address Adds or removes a static rendezvous point. Synopsis rp-address A.B.C.D no rp-addres

638 Network OS Command Reference53-1003115-01rspan-vlan2rspan-vlanConfigures the VLAN to support RSPAN (Remote Switched Port Analyzer) traffic analysi

Network OS Command Reference 63953-1003115-01rule2ruleA rule defines the permissions applicable to a particular role. Synopsis rule index [action {acc

640 Network OS Command Reference53-1003115-01scheduler2schedulerSpecifies the scheduling attributes along with the TC shape rate. Synopsis scheduler s

Network OS Command Reference 64153-1003115-01secpolicy activate2secpolicy activateActivates the defined switch connection control (SCC) policy and its

30 Network OS Command Reference53-1003115-01advertisement-interval (VRRP)2advertisement-interval (VRRP)Configures the interval at which the master VRR

642 Network OS Command Reference53-1003115-01secpolicy defined-policy2secpolicy defined-policy Creates the switch connection control (SCC) policy and

Network OS Command Reference 64353-1003115-01secpolicy defined-policy2switch(config-defined-policy-SCC_POLICY)# exitTo remove an entry from the policy

644 Network OS Command Reference53-1003115-01security-profile (AMPP)2security-profile (AMPP) Activates the security-profile mode for AMPP.Synopsis sec

Network OS Command Reference 64553-1003115-01seq (extended IP ACLs)2seq (extended IP ACLs) Inserts a rule anywhere in the IP ACL.Synopsis seq seq-valu

646 Network OS Command Reference53-1003115-01seq (extended IP ACLs)2range The policy applies to all TCP or UDP port numbers that are between the first

Network OS Command Reference 64753-1003115-01seq (extended IP ACLs)2Description Use this command to insert a rule anywhere in the IP ACL; it configure

648 Network OS Command Reference53-1003115-01seq (standard IP ACLs)2seq (standard IP ACLs)Inserts a rule anywhere in the IP ACL.Synopsis seq value {de

Network OS Command Reference 64953-1003115-01seq (extended MAC ACLs)2seq (extended MAC ACLs) Inserts a rule anywhere in the MAC ACL.Synopsis seq value

650 Network OS Command Reference53-1003115-01seq (extended MAC ACLs)2Enter no seq value to remove a rule from the MAC ACL.Hard-drop can prevent trappi

Network OS Command Reference 65153-1003115-01seq (standard MAC ACLs)2seq (standard MAC ACLs) Inserts a rule anywhere in the MAC ACL.Synopsis seq value

Network OS Command Reference 3153-1003115-01ag2agEnables Access Gateway (AG) configuration mode.Synopsis agOperands NoneDefaults NoneCommand Modes RBr

652 Network OS Command Reference53-1003115-01service password-encryption2service password-encryption Enables or disables password encryption.Synopsis

Network OS Command Reference 65353-1003115-01service-policy2service-policyBinds a policy-map to an interface. Synopsis service-policy in | out policy-

654 Network OS Command Reference53-1003115-01set as-path2set as-pathSets a prepended string or a tag for a BGP AS-path attribute in a route-map instan

Network OS Command Reference 65553-1003115-01set as-path prepend2set as-path prependPrepends an AS4 number to an AS path, makes the AS number a tag at

656 Network OS Command Reference53-1003115-01set as-path prepend2ip next-hop peer-addressSets the BGP4 next hop for a route to the neighbor address.lo

Network OS Command Reference 65753-1003115-01set automatic-tag2set automatic-tagSets the route-map tag value.Synopsis set automatic-tag valueOperands

658 Network OS Command Reference53-1003115-01set comm-list2set comm-listSets a BGP community list for deletion in a route-map instance.Synopsis set co

Network OS Command Reference 65953-1003115-01set community2set communitySets a BGP community attribute in a route-map instance.Synopsis set community

660 Network OS Command Reference53-1003115-01set cos traffic-class2set cos traffic-classSpecifies the User-Priority field value in VLAN header and tra

Network OS Command Reference 66153-1003115-01set dscp2set dscpSpecifies the DSCP field value in IP header when a packet matches a flow. Synopsis set d

Network OS Command Reference vii53-1003115-01certutil import syslogca . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68channel-group

32 Network OS Command Reference53-1003115-01ag enable2ag enableEnables Access Gateway mode on a switch.Synopsis ag [rbridge-id rbridge id vcs-id vcs-i

662 Network OS Command Reference53-1003115-01set dampening2set dampeningSets a BGP route-flap dampening penalty in a route-map instance.Synopsis set d

Network OS Command Reference 66353-1003115-01set distance2set distanceSets the administrative distance for matching OSPF routes in route-map instance.

664 Network OS Command Reference53-1003115-01set ip interface null02set ip interface null0Drops traffic when the null 0 statement becomes the active s

Network OS Command Reference 66553-1003115-01set ip next-hop2set ip next-hopSets the IPv4 address of the next hop in a route-map instance.Synopsis set

666 Network OS Command Reference53-1003115-01set local-preference2set local-preferenceSets a BGP local-preference path attribute in a route-map instan

Network OS Command Reference 66753-1003115-01set metric2set metricConfigures the route metric set clause in a route-map instance. Synopsis set metric

668 Network OS Command Reference53-1003115-01set metric-type2set metric-typeSets a variety of metric types for destination routing in a route-map inst

Network OS Command Reference 66953-1003115-01set origin2set originSets a BGP origin code in a route-map instance.Synopsis set origin [igp | incomplete

670 Network OS Command Reference53-1003115-01set-priority2set-priorityOptional command for configuring the priority map of a class-map.Synopsis set-pr

Network OS Command Reference 67153-1003115-01set route-type2set route-typeSets a route type in a route-map instance.Synopsis set route-type [internal

Network OS Command Reference 3353-1003115-01aggregate-address (BGP)2aggregate-address (BGP)Configures the device to aggregate routes from a range of n

672 Network OS Command Reference53-1003115-01set tag2set tagSets the route tag value in a route-map instance.Synopsis set tag value no set tag value O

Network OS Command Reference 67353-1003115-01set weight2set weightSets a BGP weight for the routing table in a route-map instance.Synopsis set weight

674 Network OS Command Reference53-1003115-01sflow collector2sflow collectorIdentifies the sFlow collectors to which sFlow datagrams are forwarded.Syn

Network OS Command Reference 67553-1003115-01sflow enable (global version)2sflow enable (global version) Enables sFlow globally.Synopsis sflow enable

676 Network OS Command Reference53-1003115-01sflow enable (interface version)2sflow enable (interface version) Enables sFlow on an interface.Synopsis

Network OS Command Reference 67753-1003115-01sflow polling-interval (global version)2sflow polling-interval (global version)Configures the polling int

678 Network OS Command Reference53-1003115-01sflow polling-interval (interface version)2sflow polling-interval (interface version)Configures the polli

Network OS Command Reference 67953-1003115-01sflow sample-rate (global version)2sflow sample-rate (global version)Sets the number of packets that are

680 Network OS Command Reference53-1003115-01sflow sample-rate (interface version)2sflow sample-rate (interface version)Sets the default sampling rate

Network OS Command Reference 68153-1003115-01sflow-profile2sflow-profileEstablishes an sFlow profile name and sets a sampling rate.Synopsis sflow-prof

34 Network OS Command Reference53-1003115-01alias2aliasConfigures the global or user switch alias.Synopsis alias string expansionno alias string expan

682 Network OS Command Reference53-1003115-01sfp breakout2sfp breakoutDisplays the QSFP port breakout configurations.Synopsis sfp breakoutno sfp break

Network OS Command Reference 68353-1003115-01short-path-forwarding2short-path-forwarding Enables short-path forwarding on a VRRP router. Synopsis shor

684 Network OS Command Reference53-1003115-01show access-list2show access-list Displays the status of all ACLs bound to a particular interfaceSynopsis

Network OS Command Reference 68553-1003115-01show access-list interface2show access-list interfaceDisplays the status of all ACLs bound to a particula

686 Network OS Command Reference53-1003115-01show access-list ip2show access-list ipDisplays summary information for an ACL list.Synopsis show access-

Network OS Command Reference 68753-1003115-01show access-list mac2show access-list macDisplays summary information for an ACL list.Synopsis show acces

688 Network OS Command Reference53-1003115-01show access-list-log buffer2show access-list-log bufferDisplays ACL buffer characteristics.Synopsis show

Network OS Command Reference 68953-1003115-01show ag2show agDisplays the current Access Gateway configuration on a switch.Synopsis show ag [rbridge-id

690 Network OS Command Reference53-1003115-01show ag2 Fi 5/0/2 0x020300 20:03:00:05:33:72:f5:5a 10.37.209.86 None ----------

Network OS Command Reference 69153-1003115-01show ag map2show ag mapDisplays the current VF_Port mapping to N_Ports in Access Gateway mode on a specif

Network OS Command Reference 3553-1003115-01alias-config2alias-configLaunches the alias configuration mode.Synopsis alias-configOperands NoneDefaults

692 Network OS Command Reference53-1003115-01show ag map25/0/7 0 pg0 None5/0/8 0 pg0 None-------------------------

Network OS Command Reference 69353-1003115-01show ag pg2show ag pgDisplays information on Port Grouping (PG) configured on a switch for Access Gateway

694 Network OS Command Reference53-1003115-01show arp2show arp Displays the ARP cache. Synopsis show arp [{switch_ID| all | dynamic | fortygigabitethe

Network OS Command Reference 69553-1003115-01show arp2Description Use this command to display the contents of the ARP cache.Usage Guidelines The gigab

696 Network OS Command Reference53-1003115-01show bpdu-drop2show bpdu-dropDisplays information about BPDU guard.Synopsis show bpdu-drop [interface {po

Network OS Command Reference 69753-1003115-01show capture packet interface2show capture packet interfaceDisplays information about captured packets.Sy

698 Network OS Command Reference53-1003115-01show cee maps2show cee maps Displays information on the defined CEE maps.Synopsis show cee maps default O

Network OS Command Reference 69953-1003115-01show cert-util ldapca2show cert-util ldapcaDisplays the LDAP Certification Authority (CA) certificate.Syn

700 Network OS Command Reference53-1003115-01show cert-util sshkey2show cert-util sshkeyDisplays the public SSH key.Synopsis show cert-util sshkey use

Network OS Command Reference 70153-1003115-01show cert-util syslogca2show cert-util syslogcaDisplays the syslog Certification Authority (CA) certifica

36 Network OS Command Reference53-1003115-01allow non-profiled-macs2allow non-profiled-macsSpecifies whether non-profiled MAC addresses on the profile

702 Network OS Command Reference53-1003115-01show chassis2show chassisDisplays all field-replaceable units (FRUs).Synopsis show chassis [rbridge-id rb

Network OS Command Reference 70353-1003115-01show chassis2Examples To display the FRU information on a Brocade VDX 6720-24:switch# show chassis rbridg

704 Network OS Command Reference53-1003115-01show chassis2Time Alive: 78 daysTime Awake: 1 daysSFM Slot: S2Blade Version: 3Power Consume Factor: -1

Network OS Command Reference 70553-1003115-01show chassis2Time Awake: 1 daysID: LPCSPart Num: SP750Z1ARework: APOWER SUPPLY Unit: 2Power Consume F

706 Network OS Command Reference53-1003115-01show cipherset2show ciphersetDisplays the current cipherset status.Synopsis show cipherset Operands NoneD

Network OS Command Reference 70753-1003115-01show class-maps2show class-maps Displays all the class-maps configured in the system.Synopsis show class-

708 Network OS Command Reference53-1003115-01show cli2show cli Displays all the current CLI settings.Synopsis show cli Operands NoneDefaults NoneComma

Network OS Command Reference 70953-1003115-01show cli history2show cli historyDisplays the last 512 commands executed.Synopsis show cli historyOperand

710 Network OS Command Reference53-1003115-01show clock2show clockReturns the local time, date, and time zone. Synopsis show clock [rbridge-id {rbridg

Network OS Command Reference 71153-1003115-01show config snapshot2show config snapshot Displays the snapshots present on the switch.Synopsis show conf

Network OS Command Reference 3753-1003115-01always-compare-med (BGP)2always-compare-med (BGP)Configures the device always to compare the Multi-Exit Di

712 Network OS Command Reference53-1003115-01show copy-support status2show copy-support statusDisplays the status of the copy support operation.Synops

Network OS Command Reference 71353-1003115-01show dadstatus2show dadstatusDisplays the current DHCP auto-deployment (DAD) status output on the switch.

714 Network OS Command Reference53-1003115-01show debug dhcp packet2show debug dhcp packetDisplays the DHCP packet capture configuration for interface

Network OS Command Reference 71553-1003115-01show debug dhcp packet buffer2show debug dhcp packet bufferDisplays DHCP packets saved in the DHCP packet

716 Network OS Command Reference53-1003115-01show debug dhcp packet buffer2Protocol Type : DHCPPacket Flow : RXSrc Port : 68

Network OS Command Reference 71753-1003115-01show debug ip bgp all2show debug ip bgp allDisplays all BGP4 debug options that are enabled.Synopsis show

718 Network OS Command Reference53-1003115-01show debug ip igmp2show debug ip igmpDisplays the IGMP packets received and transmitted, as well as relat

Network OS Command Reference 71953-1003115-01show debug ip pim2show debug ip pim Displays the current state of the Protocol Independent Multicast (PIM

720 Network OS Command Reference53-1003115-01show debug lacp2show debug lacpDisplays the configured debugging features for LACP.Synopsis show debug la

Network OS Command Reference 72153-1003115-01show debug lldp2show debug lldpDisplays the LLDP debugging status on the switch.Synopsis show debug lldp

38 Network OS Command Reference53-1003115-01always-propagate (BGP)2always-propagate (BGP)Enables the device to reflect routes even though they are not

722 Network OS Command Reference53-1003115-01show debug spanning-tree2show debug spanning-treeDisplays the STP debugging status on the switch.Synopsis

Network OS Command Reference 72353-1003115-01show debug udld2show debug udldShows UDLD debug status on the switch.Synopsis show debug udldOperands Non

724 Network OS Command Reference53-1003115-01show debug vrrp2show debug vrrpDisplays debug parameters. Synopsis show debug vrrp Operands NoneDefaults

Network OS Command Reference 72553-1003115-01show defaults threshold2show defaults thresholdDisplays the default thresholds for environmental and aler

726 Network OS Command Reference53-1003115-01show defaults threshold2The following example illustrates security thresholds:sw0# show defaults threshol

Network OS Command Reference 72753-1003115-01show default-vlan2show default-vlanDisplays the current default VLAN value.Synopsis show default-vlan Ope

728 Network OS Command Reference53-1003115-01show dpod2show dpodDisplays Dynamic Ports on Demand (DPOD) licensing.Synopsis show dpod [rbridge-id {rbri

Network OS Command Reference 72953-1003115-01show dpod2 1 40G ports are assigned to the Port Upgrade license 40G ports assigned to the base s

730 Network OS Command Reference53-1003115-01show diag burninerrshow2show diag burninerrshowDisplays the error messages that are stored in the nonvola

Network OS Command Reference 73153-1003115-01show diag burninerrshowerrLog2show diag burninerrshowerrLogDisplays the error log messages that are store

Network OS Command Reference 3953-1003115-01area nssa (OSPF)2area nssa (OSPF)Creates a not-so-stubby area (NSSA) or modifies its parameters.Synopsis a

732 Network OS Command Reference53-1003115-01show diag burninerrshowerrLog2iobuf.c, line: 648, comp:insmod, ltime:2012/06/03-07:2012/06/03-07:19:29:65

Network OS Command Reference 73353-1003115-01show diag burninstatus2show diag burninstatusDisplays the diagnostics burn-in status or system verificati

734 Network OS Command Reference53-1003115-01show diag post results2show diag post resultsDisplays either the brief results or detailed information of

Network OS Command Reference 73553-1003115-01show diag post results2rbridgeId 1See Also diag post enable

736 Network OS Command Reference53-1003115-01show diag setcycle2show diag setcycleDisplays the current systemVerification test parameters.Synopsis sho

Network OS Command Reference 73753-1003115-01show diag status2show diag statusDisplays the currently diagnostic test status on one or all slots in the

738 Network OS Command Reference53-1003115-01show dot1x2show dot1x Displays the overall state of dot1x on the system.Synopsis show dot1x Operands None

Network OS Command Reference 73953-1003115-01show dot1x all2show dot1x allDisplays detailed dot1x information for all of the ports.Synopsis show dot1x

740 Network OS Command Reference53-1003115-01show dot1x diagnostics interface2show dot1x diagnostics interfaceDisplays all diagnostics information for

Network OS Command Reference 74153-1003115-01show dot1x interface2show dot1x interfaceDisplays the state of a specified interface.Synopsis show dot1x

40 Network OS Command Reference53-1003115-01area range (OSPF)2area range (OSPF)Specifies area range parameters on an Area Border Router (ABR).Synopsis

742 Network OS Command Reference53-1003115-01show dot1x session-info interface2show dot1x session-info interfaceDisplays all statistical information o

Network OS Command Reference 74353-1003115-01show dot1x statistics interface2show dot1x statistics interfaceDisplays the statistics of a specified int

744 Network OS Command Reference53-1003115-01show dpod2show dpodDisplays Dynamic Ports on Demand (POD) license information.Synopsis show dpod [rbridge

Network OS Command Reference 74553-1003115-01show edge-loop-detection detail2show edge-loop-detection detailDisplays ELD detailed information for the

746 Network OS Command Reference53-1003115-01show edge-loop-detection globals2show edge-loop-detection globalsDisplays ELD global configuration values

Network OS Command Reference 74753-1003115-01show edge-loop-detection interface2show edge-loop-detection interfaceDisplays ELD interface configuration

748 Network OS Command Reference53-1003115-01show edge-loop-detection interface2Number of edge-loop-detection instances enabled: 1Interface: 7/0/5----

Network OS Command Reference 74953-1003115-01show edge-loop-detection rbridge-id2show edge-loop-detection rbridge-idDisplays ELD status information fo

750 Network OS Command Reference53-1003115-01show environment fan2show environment fanDisplays fan status information.Synopsis show environment fan [r

Network OS Command Reference 75153-1003115-01show environment history2show environment historyDisplays the field-replaceable unit (FRU) history log.Sy

Network OS Command Reference 4153-1003115-01area stub (OSPF)2area stub (OSPF)Creates a stub area or modifies its parameters. Synopsis area {A.B.C.D |

752 Network OS Command Reference53-1003115-01show environment history2Factory Part Number: Not AvailableFactory Serial Number: Not AvailablePOWER SUPP

Network OS Command Reference 75353-1003115-01show environment power2show environment powerDisplays power supply status.Synopsis show environment power

754 Network OS Command Reference53-1003115-01show environment sensor2show environment sensorDisplays the environment sensor status.Synopsis show envir

Network OS Command Reference 75553-1003115-01show environment temp2show environment tempDisplays environment temperature.Synopsis show environment tem

756 Network OS Command Reference53-1003115-01show fabric all2show fabric allDisplays the Brocade VCS Fabric membership information. Synopsis show fabr

Network OS Command Reference 75753-1003115-01show fabric ecmp load-balance2show fabric ecmp load-balance Displays the current configuration of hash fi

758 Network OS Command Reference53-1003115-01show fabric isl2show fabric islDisplays Inter-Switch Link (ISL) information in the fabric.Synopsis show f

Network OS Command Reference 75953-1003115-01show fabric isl2When a switch in a fabric is running Network OS 4.0.1 or later, CLI output displays the Q

760 Network OS Command Reference53-1003115-01show fabric isl2switch# sh fab islRbridge-id: 1 #ISLs: 4 Src Src Nbr NbrIndex Interface Index Interfa

Network OS Command Reference 76153-1003115-01show fabric isl2Src Src Nbr NbrIndex Interface Index Interface Nbr-WWN BW Trunk Nbr-Name-----------------

viii Network OS Command Reference53-1003115-01clear logging auditlog. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132clear logging

42 Network OS Command Reference53-1003115-01area virtual-link (OSPF)2area virtual-link (OSPF)Creates or modifies virtual links for an area.Synopsis ar

762 Network OS Command Reference53-1003115-01show fabric islports2show fabric islports Displays information for all Inter-Switch Link (ISL) ports in t

Network OS Command Reference 76353-1003115-01show fabric islports2Down, (Reason Code) The ISL is down due to the given reason code.In this command, I

764 Network OS Command Reference53-1003115-01show fabric islports2Usage Guidelines This command is not available in standalone mode. If this command i

Network OS Command Reference 76553-1003115-01show fabric islports2See Also fabric isl enable, show diag burninstatus, show fabric isl, show fabric tru

766 Network OS Command Reference53-1003115-01show fabric port-channel2show fabric port-channelDisplays the fabric VLAG load-balance information.Synops

Network OS Command Reference 76753-1003115-01show fabric route linkinfo2show fabric route linkinfoDisplays the RBridge route link information connecte

768 Network OS Command Reference53-1003115-01show fabric route linkinfo2Examples To display link information for the fabric: switch# show fabric route

Network OS Command Reference 76953-1003115-01show fabric route linkinfo2This example displays link linformation and includes the breakout index of the

770 Network OS Command Reference53-1003115-01show fabric route linkinfo24 3 Te 48/0/49 34 Te 1/0/49 500 Pt_Pt EthernetThis example displays link

Network OS Command Reference 77153-1003115-01show fabric route multicast2show fabric route multicastDisplays ISLs that receives any forwarded Broadcas

Network OS Command Reference 4353-1003115-01area virtual-link (OSPF)2retransmit-interval time Time between Link State Advertisement (LSA) retransmissi

772 Network OS Command Reference53-1003115-01show fabric route multicast2Rbridge-id: 1Mcast Priority: 1Enet IP Addr: 10.24.85.212WWN: 10:00:00:05:1e:c

Network OS Command Reference 77353-1003115-01show fabric route multicast2Root of the Multicast-Tree========================== Rbridge-id: 1 Mcast Prio

774 Network OS Command Reference53-1003115-01show fabric route neighbor-state2show fabric route neighbor-stateDisplays the state information of all th

Network OS Command Reference 77553-1003115-01show fabric route neighbor-state2The show fabric family of commands display neighbor and local port infor

776 Network OS Command Reference53-1003115-01show fabric route neighbor-state2Src Src Nbr Nbr Nbr Index Interface Index Interface State------------

Network OS Command Reference 77753-1003115-01show fabric route pathinfo2show fabric route pathinfoDisplays the path of a data stream through a fabric

778 Network OS Command Reference53-1003115-01show fabric route pathinfo2Regardless of parameter selection, the command displays the following status o

Network OS Command Reference 77953-1003115-01show fabric route pathinfo2intervals, and the counter is incremented if the condition is true. Each sampl

780 Network OS Command Reference53-1003115-01show fabric route pathinfo2To show path information with basic statistics:switch# show fabric route pathi

Network OS Command Reference 78153-1003115-01show fabric route pathinfo2Hop In Port Domain ID Out Port BW Cost------------------------------------

44 Network OS Command Reference53-1003115-01arp2arpEnables specification of an IPv4 address for an Address Resolution Protocol (ARP) entry.Synopsis ar

782 Network OS Command Reference53-1003115-01show fabric route pathinfo2Hop In Port Domain ID Out Port BW Cost------------------------------------

Network OS Command Reference 78353-1003115-01show fabric route pathinfo2TxCrdz (1s) 0 -- 0 --TxCrdz (64s) 0 -- 0 --F/s (1s) 0 0 0 0F/s (64s) 0

784 Network OS Command Reference53-1003115-01show fabric route pathinfo2Hop In Port Domain ID Out Port BW Cost------------------------------------

Network OS Command Reference 78553-1003115-01show fabric route topology2show fabric route topologyDisplays the RBridge routes from the source switch t

786 Network OS Command Reference53-1003115-01show fabric route topology2When a fabric is running normal mode (switches are running Network OS 4.1.0 or

Network OS Command Reference 78753-1003115-01show fabric route topology21 48 30 Te 1/0/49 1 500 1 Te 48/0/49 40G YesThis example displays route topolo

788 Network OS Command Reference53-1003115-01show fabric trunk2show fabric trunk Displays Inter-Switch Link (ISL) trunk information.Synopsis show fabr

Network OS Command Reference 78953-1003115-01show fabric trunk2Examples To display the fabric trunk information:switch# show fabric trunk Possible com

790 Network OS Command Reference53-1003115-01show fabric trunk2Trunk Src Source Nbr Nbr Group Index Interface Index Interface Nbr-WWN----------------

Network OS Command Reference 79153-1003115-01show fcoe fabric-map2show fcoe fabric-mapDisplays the FCoE fabric-map configuration globally in a fabric,

Network OS Command Reference 4553-1003115-01as-path-ignore (BGP)2as-path-ignore (BGP)Disables the comparison of the autonomous system (AS) path length

792 Network OS Command Reference53-1003115-01show fcoe fabric-map2fcoefabric-map defaultfcoe-enode 200!sw0# show running-config rbridge-id 20rbridge-

Network OS Command Reference 79353-1003115-01show fcoe interface2show fcoe interface Displays a synopsis of the FCoE interfaces.Synopsis show fcoe int

794 Network OS Command Reference53-1003115-01show fcoe login2show fcoe login Displays FCoE login information.Synopsis show fcoe login {interface [WORD

Network OS Command Reference 79553-1003115-01show fcoe map2show fcoe map Displays all FCoE maps, or a single map. Synopsis show fcoe map [default {rbr

796 Network OS Command Reference53-1003115-01show fcsp auth-secret dh-chap2show fcsp auth-secret dh-chapDisplays the switches (WWNs) for which a share

Network OS Command Reference 79753-1003115-01show fibrechannel login2show fibrechannel loginDisplays fibrechannel logins.Synopsis show fibrechannel lo

798 Network OS Command Reference53-1003115-01show fibrechannel login2To view fibrechannel logins on an interface:sw0# show fibrechannel login interfac

Network OS Command Reference 79953-1003115-01show file2show fileDisplays the contents of a file.Synopsis show file filename Operands filename The name

800 Network OS Command Reference53-1003115-01show fips2show fipsDisplays the current FIPS configuration.Synopsis show fips Operands NoneDefaults NoneC

Network OS Command Reference 80153-1003115-01show firmwaredownloadhistory2show firmwaredownloadhistoryDisplays the firmware download history for the s

46 Network OS Command Reference53-1003115-01auto-cost reference-bandwidth (OSPF)2auto-cost reference-bandwidth (OSPF)Configures reference bandwidth.Sy

802 Network OS Command Reference53-1003115-01show firmwaredownloadstatus2show firmwaredownloadstatusDisplays the firmware download activity log.Synops

Network OS Command Reference 80353-1003115-01show firmwaredownloadstatus2To display a high-level summary of the firmware download status:switch# show

804 Network OS Command Reference53-1003115-01show global-running-config2show global-running-configDisplays the global running configuration.Synopsis s

Network OS Command Reference 80553-1003115-01show global-running-config2cee-map default precedence 1 priority-group-table 1 weight 40 pfc on priority-

806 Network OS Command Reference53-1003115-01show ha2show haDisplays the High Availability (HA) status of the management modules.Synopsis show ha [all

Network OS Command Reference 80753-1003115-01show ha2Usage Guidelines HA is not supported in this release. All failover is disruptive. The HA commands

808 Network OS Command Reference53-1003115-01show history2show historyDisplays the history of commands executed on the switch.Synopsis show history [n

Network OS Command Reference 80953-1003115-01show interface2show interface Displays the detailed interface configuration and capabilities of all inter

810 Network OS Command Reference53-1003115-01show interface2port Specifies a valid port number.switchport Specifies to display information for Layer 2

Network OS Command Reference 81153-1003115-01show interface2Errors: 0, Discards: 0Transmit Statistics:0 packets, 0 bytesUnicasts: 0, Multicasts: 0, Br

Network OS Command Reference 4753-1003115-01auto-qos enable2auto-qos enableEnables the Auto-QoS for NAS (automatic network attached storage) feature.S

812 Network OS Command Reference53-1003115-01show interface2Inactive Vlans : 100Interface name : Ten Gigabit Ethernet 1/0/20Switchport mode : trunkIn

Network OS Command Reference 81353-1003115-01show interface description2show interface descriptionDisplays the interface description.Synopsis show int

814 Network OS Command Reference53-1003115-01show interface FibreChannel2show interface FibreChannelDisplays Fibre Channel port hardware statistics.Sy

Network OS Command Reference 81553-1003115-01show interface FibreChannel2The second column displays link error status block counters.Link_failure Link

816 Network OS Command Reference53-1003115-01show interface FibreChannel2tim_txcrd_z The number of times that the port was unable to transmit frames b

Network OS Command Reference 81753-1003115-01show interface FibreChannel2LD—Link is from 5 km through 10 km.LE—Distance is determined dynamically.LS—D

818 Network OS Command Reference53-1003115-01show interface FibreChannel2Free_buffer: 0 Address_err: 0Overrun: 0 Lr_in: 1Suspended: 0 Lr_out: 1Par

Network OS Command Reference 81953-1003115-01show interface FibreChannel2er_type2_miss 0 frames with FTB Type 2 misser_type6_miss 0 frames with FT

820 Network OS Command Reference53-1003115-01show interface management2show interface managementDisplays information related to a management interface

Network OS Command Reference 82153-1003115-01show interface management2line-speed configured AutoThe following example displays information related to

48 Network OS Command Reference53-1003115-01backup-advertisement-interval2backup-advertisement-intervalConfigures the interval at which backup VRRP ro

822 Network OS Command Reference53-1003115-01show interface stats2show interface statsDisplays interface statistics for a variety of interfaces.Synops

Network OS Command Reference 82353-1003115-01show interface stats2 Multicasts 0 0 Broadc

824 Network OS Command Reference53-1003115-01show interface status2show interface statusDisplays the interface status.Synopsis show interface status [

Network OS Command Reference 82553-1003115-01show interface trunk2show interface trunkDisplays the interface trunk information.Synopsis show interface

826 Network OS Command Reference53-1003115-01show inventory2show inventoryDisplays the hardware inventory of the switch.Synopsis show inventory [chass

Network OS Command Reference 82753-1003115-01show inventory2SID:BR-VDX8770-4 SwitchType:1000PN:84-1001681-03 SN:BZA0305H00DSee Also None

828 Network OS Command Reference53-1003115-01show ip bgp2show ip bgpDisplays BGP information.Synopsis show ip bgp {summary} [rbridge-id rbridge-id]Ope

Network OS Command Reference 82953-1003115-01show ip bgp attribute-entries2show ip bgp attribute-entriesDisplays BGP4 route-attribute entries that are

830 Network OS Command Reference53-1003115-01show ip bgp dampened-paths2show ip bgp dampened-pathsDisplays all BGP4 dampened routes.Synopsis show ip b

Network OS Command Reference 83153-1003115-01show ip bgp filtered-routes2show ip bgp filtered-routesDisplays BGP4 filtered routes that are received fr

Network OS Command Reference 4953-1003115-01banner incoming2banner incomingSets the incoming banner message.Synopsis banner incoming messageno banner

832 Network OS Command Reference53-1003115-01show ip bgp flap-statistics2show ip bgp flap-statisticsDisplays BGP4 route-dampening statistics for all d

Network OS Command Reference 83353-1003115-01show ip bgp neighbor2show ip bgp neighborDisplays configuration information and statistics for BGP4 neigh

834 Network OS Command Reference53-1003115-01show ip bgp neighbors2show ip bgp neighborsDisplays configuration information and statistics for BGP4 nei

Network OS Command Reference 83553-1003115-01show ip bgp neighbors advertised-routes2show ip bgp neighbors advertised-routesDisplays configuration inf

836 Network OS Command Reference53-1003115-01show ip bgp neighbors flap-statistics2show ip bgp neighbors flap-statisticsDisplays configuration informa

Network OS Command Reference 83753-1003115-01show ip bgp neighbors received2show ip bgp neighbors receivedDisplays Outbound Route Filters (ORFs) recei

838 Network OS Command Reference53-1003115-01show ip bgp neighbors received-routes2show ip bgp neighbors received-routesLists all route information re

Network OS Command Reference 83953-1003115-01show ip bgp neighbors routes2show ip bgp neighbors routesLists a variety of route information received in

840 Network OS Command Reference53-1003115-01show ip bgp neighbors routes-summary2show ip bgp neighbors routes-summaryLists all route information rece

Network OS Command Reference 84153-1003115-01show ip bgp peer-group2show ip bgp peer-groupDisplays peer-group information.Synopsis show ip bgp peer-gr

50 Network OS Command Reference53-1003115-01banner login2banner loginSets the switch banner.Synopsis banner login message no banner login Operands mes

842 Network OS Command Reference53-1003115-01show ip bgp routes2show ip bgp routes Displays BGP4 route information that is filtered by the table entry

Network OS Command Reference 84353-1003115-01show ip bgp routes age2show ip bgp routes age Displays BGP4 route information that is filtered by age, be

844 Network OS Command Reference53-1003115-01show ip bgp routes as-path-access-list2show ip bgp routes as-path-access-listDisplays BGP4 route informat

Network OS Command Reference 84553-1003115-01show ip bgp routes community2show ip bgp routes community Displays BGP4 route information that is filtere

846 Network OS Command Reference53-1003115-01show ip bgp routes community-access-list2show ip bgp routes community-access-listDisplays BGP4 route info

Network OS Command Reference 84753-1003115-01show ip bgp routes community-reg-expression2show ip bgp routes community-reg-expressionDisplays BGP4 rout

848 Network OS Command Reference53-1003115-01show ip bgp routes longer-prefixes2show ip bgp routes longer-prefixesDisplays BGP4 route information that

Network OS Command Reference 84953-1003115-01show ip bgp routes neighbor nexthop local unreachable2show ip bgp routes neighbor nexthop local unreachab

850 Network OS Command Reference53-1003115-01show ip bgp routes prefix-list regular-expression route-map2show ip bgp routes prefix-list regular-expres

Network OS Command Reference 85153-1003115-01show ip bgp routes summary detail2show ip bgp routes summary detailDisplays BGP4 summary route informatio

Network OS Command Reference 5153-1003115-01banner login2Welcome to NOS CLIuser connected from ::FFFF:10.103.8.61 using ssh on abc.comswitch#See Also

852 Network OS Command Reference53-1003115-01show ip dhcp relay address interface2show ip dhcp relay address interface Displays IP DHCP Relay addresse

Network OS Command Reference 85353-1003115-01show ip dhcp relay address interface2Examples Display configured IP DHCP Relay addresses on a specific ph

854 Network OS Command Reference53-1003115-01show ip dhcp relay address rbridge-id2show ip dhcp relay address rbridge-id Displays IP DHCP Relay addres

Network OS Command Reference 85553-1003115-01show ip dhcp relay address rbridge-id2See Also show ip dhcp relay address interface, ip dhcp relay addres

856 Network OS Command Reference53-1003115-01show ip dhcp relay statistics2show ip dhcp relay statisticsDisplays the general information about the DHC

Network OS Command Reference 85753-1003115-01show ip dhcp relay statistics2No Offers: 0To display statistics for specific RBridge IDs:sw0# show ip dhc

858 Network OS Command Reference53-1003115-01show ip igmp groups2show ip igmp groupsDisplays information related to learned groups in the IGMP protoco

Network OS Command Reference 85953-1003115-01show ip igmp groups2port-channel number Specifies the interface is a port-channel. The number of availab

860 Network OS Command Reference53-1003115-01show ip igmp groups2See Also None

Network OS Command Reference 86153-1003115-01show ip igmp interface2show ip igmp interfaceDisplays information related to VLANs in the IGMP protocol m

Network OS Command Reference ix53-1003115-01debug ip ospf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .185debug ip pim

52 Network OS Command Reference53-1003115-01banner motd2banner motd Sets the message of the day (MOTD) banner.Synopsis banner motd messageno banner mo

862 Network OS Command Reference53-1003115-01show ip igmp interface2port-channel number Specifies the interface is a port-channel. The number of avai

Network OS Command Reference 86353-1003115-01show ip igmp snooping2show ip igmp snoopingDisplays IGMP snooping information.Synopsis show ip igmp snoop

864 Network OS Command Reference53-1003115-01show ip igmp statistics2show ip igmp statistics Displays IGMP statistics.Synopsis show ip igmp statistics

Network OS Command Reference 86553-1003115-01show ip igmp statistics2• When the rbridge-id option is specified, details for the VE interface on that p

866 Network OS Command Reference53-1003115-01show ip interface2show ip interface Displays the IP interface status and configuration of all interfaces

Network OS Command Reference 86753-1003115-01show ip interface2Note the following with respect to the show ip interface brief command:• The command sh

868 Network OS Command Reference53-1003115-01show ip interface2Ten Gigabit Ethernet 1/0/9 unassigned up upTen Gigabit Ethernet 1/0/10 unassigned up

Network OS Command Reference 86953-1003115-01show ip interface loopback2show ip interface loopbackDisplays loopback information for a Management Clust

870 Network OS Command Reference53-1003115-01show ip interface ve2show ip interface veDisplays virtual Ethernet (VE) port information for a Management

Network OS Command Reference 87153-1003115-01show ip ospf2show ip ospfDisplays the OSPF state.Synopsis show ip ospf [vrf name [rbridge-id {rbridge-id

Network OS Command Reference 5353-1003115-01bgp-redistribute-internal (BGP)2bgp-redistribute-internal (BGP)Causes the device to allow the redistributi

872 Network OS Command Reference53-1003115-01show ip ospf area2show ip ospf areaDisplays the OSPF area table.Synopsis show ip ospf area {A.B.C.D | dec

Network OS Command Reference 87353-1003115-01show ip ospf area2all Displays the information for the physical, loopback, and SVI interfaces of all node

874 Network OS Command Reference53-1003115-01show ip ospf border-routers2show ip ospf border-routersDisplays information about border routers and boun

Network OS Command Reference 87553-1003115-01show ip ospf config2show ip ospf configDisplays OSPF configuration.Synopsis show ip ospf config [[vrf vrf

876 Network OS Command Reference53-1003115-01show ip ospf database2show ip ospf database Shows database information.Synopsis show ip ospf database [[v

Network OS Command Reference 87753-1003115-01show ip ospf database2router-id routerid Displays LSAs for the advertising router that you specify.self-o

878 Network OS Command Reference53-1003115-01show ip ospf database2Index Age LS ID Router Netmask Metric Flag Fwd Address1 1248 1.0.5.0 1.0.0.1 f

Network OS Command Reference 87953-1003115-01show ip ospf interface2show ip ospf interfaceDisplays interface information.Synopsis show ip ospf interfa

880 Network OS Command Reference53-1003115-01show ip ospf interface2all Displays the information for the physical, loopback, and SVI interfaces of all

Network OS Command Reference 88153-1003115-01show ip ospf neighbor2show ip ospf neighbor Displays neighbor information.Synopsis show ip ospf neighbor

54 Network OS Command Reference53-1003115-01bind2bindUsed to create a persistent binding between the logical FCoE port and the ten/forty gigabit or LA

882 Network OS Command Reference53-1003115-01show ip ospf neighbor2Defaults None Command Modes Privileged EXEC modeDescription Use this command to dis

Network OS Command Reference 88353-1003115-01show ip ospf redistribute route2show ip ospf redistribute route Displays redistributed routes.Synopsis sh

884 Network OS Command Reference53-1003115-01show ip ospf routes2show ip ospf routesDisplays routes.Synopsis show ip ospf routes [A.B.C.D] [[vrf vrfna

Network OS Command Reference 88553-1003115-01show ip ospf summary2show ip ospf summaryDisplays summary information for all OSPF instances.Synopsis sho

886 Network OS Command Reference53-1003115-01show ip ospf traffic2show ip ospf trafficDisplays OSPF traffic details.Synopsis show ip ospf traffic [{fo

Network OS Command Reference 88753-1003115-01show ip ospf traffic2Description Use this command to display details of OSPF traffic sent and received. Y

888 Network OS Command Reference53-1003115-01show ip ospf virtual2show ip ospf virtual Displays information about virtual links.Synopsis show ip ospf

Network OS Command Reference 88953-1003115-01show ip pim bsr2show ip pim bsrDisplays the Boot Strap Router (BSR) information.Synopsis show ip pim bsr

890 Network OS Command Reference53-1003115-01show ip pim group2show ip pim groupDisplays the list of multicast groups.Synopsis show ip pim group [rbri

Network OS Command Reference 89153-1003115-01show ip pim mcache2show ip pim mcacheDisplays the multicast cache.Synopsis show ip pim mcache [ip-address

Network OS Command Reference 5553-1003115-01bpdu-drop enable2bpdu-drop enableDrops STP, RSTP, MSTP, and PVST and RPVST bridge protocol data units (BPD

892 Network OS Command Reference53-1003115-01show ip pim neighbor2show ip pim neighborDisplays the Protocol Independent Multicast (PIM) neighbor infor

Network OS Command Reference 89353-1003115-01show ip pim rpf2show ip pim rpf Displays the Reverse Path Forwarding (RPF) for a given unicast IP address

894 Network OS Command Reference53-1003115-01show ip pim rp-hash2show ip pim rp-hash Displays the Rendezvous Point (RP) information for a Protocol Ind

Network OS Command Reference 89553-1003115-01show ip pim rp-map2show ip pim rp-mapDisplays the Rendezvous Point (RP) to group mappings.Synopsis show i

896 Network OS Command Reference53-1003115-01show ip pim rp-set2show ip pim rp-setDisplays the Rendezvous Point (RP) set list.Synopsis show ip pim rp-

Network OS Command Reference 89753-1003115-01show ip pim-sparse2show ip pim-sparseDisplays the Protocol Independent Multicast (PIM) router parameters.

898 Network OS Command Reference53-1003115-01show ip pim-sparse2 Join/Prune interval: 60 Inactivity interval: 180 Hardware drop enabled: Yes Prune wai

Network OS Command Reference 89953-1003115-01show ip pim traffic2show ip pim trafficDisplays the Protocol Independent Multicast (PIM) traffic statisti

900 Network OS Command Reference53-1003115-01show ip route2show ip routeShows IP route information. Synopsis show ip route show ip route A.B.C.D/M [{d

Network OS Command Reference 90153-1003115-01show ip route2Destination Gateway Port Cost Type Uptime1 1.1.1.0/24 DIRECT Te 2/1 0/0 D 1m57s 2 1.1.

56 Network OS Command Reference53-1003115-01bridge-priority2bridge-prioritySpecifies the priority of the bridge. Synopsis bridge-priority priority no

902 Network OS Command Reference53-1003115-01show ip route2Type Codes - B:BGP D:Connected I:ISIS O:OSPF R:RIP S:Static; Cost - Dist/MetricBGP Codes -

Network OS Command Reference 90353-1003115-01show ipv6 route2show ipv6 routeDisplays the IPv6 route information.Synopsis show lipv6 routeOperands None

904 Network OS Command Reference53-1003115-01show lacp2show lacpDisplays Link Aggregation Control Protocol (LACP) statistics.Synopsis show lacp [count

Network OS Command Reference 90553-1003115-01show lacp sys-id2show lacp sys-idDisplays the Link Aggregation Control Protocol (LACP) system ID and prio

906 Network OS Command Reference53-1003115-01show license2show licenseDisplays license information.Synopsis show license [rbridge-id {rbridge-id ID |

Network OS Command Reference 90753-1003115-01show license2See Also license add, license remove, show license id

908 Network OS Command Reference53-1003115-01show license id2show license idDisplays the RBridge License ID.Synopsis show license id [rbridge-id {rbri

Network OS Command Reference 90953-1003115-01show linecard2show linecardDisplays information about the interface modules (line cards) present in the c

910 Network OS Command Reference53-1003115-01show linecard2Usage Guidelines NoneExamples To display the interface modules present in a Brocade VDX 877

Network OS Command Reference 91153-1003115-01show lldp interface2show lldp interface Displays the LLDP status on the specified interface.Synopsis show

Network OS Command Reference 5753-1003115-01capability as4 (BGP)2capability as4 (BGP)Enables 4-byte autonomous system number (ASN) capability at the B

912 Network OS Command Reference53-1003115-01show lldp neighbors2show lldp neighbors Displays LLDP information for all neighboring devices on the spec

Network OS Command Reference 91353-1003115-01show lldp neighbors2System Description: Fibre Channel Switch.System Capabilities: Switching RoutingSystem

914 Network OS Command Reference53-1003115-01show lldp statistics2show lldp statistics Displays the LLDP statistics on all interfaces or a specified i

Network OS Command Reference 91553-1003115-01show logging auditlog2show logging auditlogDisplays the internal audit log buffer of the switch.Synopsis

916 Network OS Command Reference53-1003115-01show logging raslog2show logging raslogDisplays the internal RASlog buffer of the switch.Synopsis show lo

Network OS Command Reference 91753-1003115-01show logging raslog2To display all RASLog messages for an interface module: switch# show logging raslog b

918 Network OS Command Reference53-1003115-01show mac-address-table2show mac-address-tableDisplays forwarding information for all MAC addresses, for a

Network OS Command Reference 91953-1003115-01show mac-address-table2port Specifies a valid port number.gigabitethernet rbridge-id/slot/port Specifies

920 Network OS Command Reference53-1003115-01show mac-address-table2To display a dynamic MAC address table:switch# show mac-address-table dynamic vlan

Network OS Command Reference 92153-1003115-01show media2show mediaDisplays the SFP information for all the interfaces present on a switch.Synopsis sho

58 Network OS Command Reference53-1003115-01capture packet interface2capture packet interfaceEnables the capture of packet information on an interface

922 Network OS Command Reference53-1003115-01show media interface2show media interfaceDisplays the SFP information for a specific interface.Synopsis s

Network OS Command Reference 92353-1003115-01show media interface2Vendor Rev 01Options 001a Remote fault/Jabber detect/copper link upTemperature thres

924 Network OS Command Reference53-1003115-01show media interface2DD Type 0x68Enh Options 0xfaStatus/Ctrl 0x82Alarm flags[0,1] 0x5, 0x40Warn Flags[0,1

Network OS Command Reference 92553-1003115-01show media linecard2show media linecardDisplays the SFP information for a specified interface module.Syno

926 Network OS Command Reference53-1003115-01show media linecard2Baud Rate 103 (units 100 megabaud)Length 9u 0 (units km)Length 9u 50 (units 100 mete

Network OS Command Reference 92753-1003115-01show mm2show mmDisplays information about the Management Modules present in the chassis.Synopsis show mm

928 Network OS Command Reference53-1003115-01show monitor2show monitor Displays the monitoring information for all Port Mirroring sessions.Synopsis sh

Network OS Command Reference 92953-1003115-01show name-server brief2show name-server briefDisplays brief entries of local name server (NS) information

930 Network OS Command Reference53-1003115-01show name-server detail2show name-server detail Displays local name server (NS) information about devices

Network OS Command Reference 93153-1003115-01show name-server detail2Share Area The state of the Brocade shared area addressing method. If “Yes” then

Network OS Command Reference 5953-1003115-01capture packet interface2NOTEThe all option is not supported for enabling packet capture.To view the captu

932 Network OS Command Reference53-1003115-01show name-server nodefind2show name-server nodefind Displays the local name server (NS) information for a

Network OS Command Reference 93353-1003115-01show name-server zonemember2show name-server zonemember Displays the local name server (NS) zoning inform

934 Network OS Command Reference53-1003115-01show name-server zonemember2See Also show name-server brief, show name-server detail, show name-server no

Network OS Command Reference 93553-1003115-01show nas statistics2show nas statistics Displays automatic network attached storage (Auto NAS)) statistic

936 Network OS Command Reference53-1003115-01show netconf client-capabilities2show netconf client-capabilitiesDisplays the client capabilities associa

Network OS Command Reference 93753-1003115-01show netconf-state capabilities2show netconf-state capabilitiesDisplays NETCONF server capabilities.Synop

938 Network OS Command Reference53-1003115-01show netconf-state datastores2show netconf-state datastoresDisplays the NETCONF datastores that are prese

Network OS Command Reference 93953-1003115-01show netconf-state schemas2show netconf-state schemasDisplays the data models supported by the NETCONF se

940 Network OS Command Reference53-1003115-01show netconf-state sessions2show netconf-state sessionsDisplays information about currently active NETCON

Network OS Command Reference 94153-1003115-01show netconf-state statistics2show netconf-state statisticsDisplays NETCONF server statistics.Synopsis sh

60 Network OS Command Reference53-1003115-01cbs2cbs Mandatory command for configuring the controlled burst size for a class-map.Synopsis cbs cbs-sizen

942 Network OS Command Reference53-1003115-01show notification stream2show notification streamDisplays notifications about the event stream.Synopsis s

Network OS Command Reference 94353-1003115-01show ntp status2show ntp status Displays the current active NTP server IP address or LOCL (for local swit

944 Network OS Command Reference53-1003115-01show overlapping-vlan-resource linecard2show overlapping-vlan-resource linecardShows the utilization of t

Network OS Command Reference 94553-1003115-01show policymap2show policymap Displays configured policy-maps and class-map Policer parameters applied to

946 Network OS Command Reference53-1003115-01show policymap2switch# show policymap interface tengigabitethernet 4/1 inputInterface : Ten Gigabit Ether

Network OS Command Reference 94753-1003115-01show port port-channel2show port port-channel Displays the detailed LACP attributes.Synopsis show port po

948 Network OS Command Reference53-1003115-01show port-channel2show port-channelDisplays the Link Aggregation Group (LAG) information for a port-chann

Network OS Command Reference 94953-1003115-01show port-profile2show port-profileDisplays the AMPP port-profile configuration information.Synopsis show

950 Network OS Command Reference53-1003115-01show port-profile domain2show port-profile domain Displays the status of Automatic Migration of Port Prof

Network OS Command Reference 95153-1003115-01show port-profile interface2show port-profile interface Displays AMPP port-profile information for interf

Network OS Command Reference 6153-1003115-01cee2ceeApplies a Converged Enhanced Ethernet (CEE) provisioning map on an interface.Synopsis cee default n

952 Network OS Command Reference53-1003115-01show port-profile name2show port-profile nameDisplays the port profile information for a named port-profi

Network OS Command Reference 95353-1003115-01show port-security2show port-securityDisplays the configuration information related to port security.Syno

954 Network OS Command Reference53-1003115-01show port-security addresses2show port-security addressesDisplays the configuration information related t

Network OS Command Reference 95553-1003115-01show port-security interface2show port-security interfaceDisplays the configuration information related t

956 Network OS Command Reference53-1003115-01show port-security interface2Violation time : Fri Mar 22 05:53:03 UTC 2013Shutdown time(in Minutes)

Network OS Command Reference 95753-1003115-01show port-security oui interface2show port-security oui interfaceDisplays the configuration information r

958 Network OS Command Reference53-1003115-01show port-security sticky interface2show port-security sticky interfaceDisplays the configuration informa

Network OS Command Reference 95953-1003115-01show process cpu2show process cpu Displays information about the active processes in the switch and their

960 Network OS Command Reference53-1003115-01show process info2show process infoDisplays system processes hierarchically.Synopsis show process info [r

Network OS Command Reference 96153-1003115-01show process memory2show process memory Displays the memory usage information based on processes running