Brocade Virtual ADX Switch and Router Guide (Supporting AD Manual do Utilizador Página 210
- Página / 374
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
196 Brocade Virtual ADX Switch and Router Guide
53-1003246-01
Displaying OSPFv3 information
7
Displaying OSPFv3 SPF information
You can display the following OSPFv3 SPF information:
• SPF node information for a specified area.
• SPF table for a specified area.
• SPF tree for a specified area.
For example, to display information about SPF nodes in area 0, enter the following command at any
level of the CLI:
Syntax: show ipv6 ospf spf node area [area-id]
The node keyword displays SPF node information.
The area area-id parameter specifies a particular area. You can specify the area-id in the following
formats:
Options A 24-bit field that enables IPv6 OSPF routers to support the optional
capabilities. When set, the following bits indicate the following:
V6 – The device should be included in IPv6 routing calculations.
E – The device floods AS-external-LSAs as described in RFC 2740.
MC – The device forwards multicast packets as described in RFC 1586.
N – The device handles type 7 LSAs as described in RFC 1584.
R – The originator is an active router.
DC –The device handles demand circuits.
Area The area whose link state information has led to the routing table entry's
collection of paths.
Cost The type 1 cost of this route.
Type2 Cost The type 2 cost of this route.
Next-Hop Router The IPv6 address of the next router a packet must traverse to reach a
destination.
Outgoing Interface The router interface through which a packet must traverse to reach the
next-hop router.
TABLE 32 OSPFv3 route information (Continued)
This Field... Displays...
Virtual ADX# show ipv6 ospf spf node area 0
SPF node for Area 0
SPF node 223.223.223.223, cost: 0, hops: 0
nexthops to node:
parent nodes:
child nodes: 223.223.223.223:88
SPF node 223.223.223.223:88, cost: 1, hops: 1
nexthops to node: :: ethe 3
parent nodes: 223.223.223.223
child nodes: 1.1.1.1:0
SPF node 1.1.1.1:0, cost: 1, hops: 2
nexthops to node: fe80::2e0:52ff:fe91:bb37 ethe 3
parent nodes: 223.223.223.223:88
child nodes:
- Brocade Virtual ADX 1
- Document History 2
- Contents 3
- Chapter 4 Configuring IP 4
- Chapter 5 Rate Limiting 5
- Chapter 6 Configuring OSPF 5
- Chapter 7 Configuring OSPFv3 6
- Chapter 9 Configuring BGP4+ 9
- 53-1003246-01 10
- Document conventions 11
- Command syntax conventions 12
- Notes, cautions, and warnings 12
- Brocade resources 13
- Document feedback 14
- Configuring Basic Features 15
- • The time stamp 19
- • The user name 19
- Configuring CLI banners 22
- Configuring terminal display 24
- Assigning a port name 25
- Changing the MAC age time 26
- Enabling port-based VLANs 27
- Displaying mac addresses 29
- TABLE 2 System parameters 30
- System parameter Description 31
- Configuring Basic Layer 3 33
- Disabling Layer 2 switching 34
- Additional features 35
- Overview 37
- Default VLAN 39
- 802.1q tagging 40
- Virtual routing interfaces 42
- • Dynamic ports 43
- Dynamic ports 44
- Static ports 45
- Excluded ports 45
- Broadcast leaks 45
- Routing between VLANs 46
- Dynamic port assignment 47
- Configuring port-based VLANs 48
- Modifying a port-based VLAN 50
- Configuring IP subnet VLANs 51
- Displaying VLAN information 58
- Configuring IP 61
- IP route table 62
- IP forwarding cache 63
- IP access policies 64
- IP global parameters 65
- • Redirect messages 66
- IP interface parameters 67
- Configuring IP parameters 68
- VADX-DUT3(config)#int eth 1 69
- Deleting an IP address 70
- Defining a DNS entry 73
- Defining a domain name 74
- Defining DNS servers 74
- Changing the router ID 75
- Configuring ARP parameters 77
- Changing the TTL threshold 79
- Disabling ICMP messages 81
- Configuring static routes 82
- Configuring a static IP route 84
- Configuring a “Null” route 85
- Configuring IP load sharing 91
- How IP load sharing works 93
- Virtual ADX(config)# int e 1 98
- Displaying IP information 99
- This field... Displays 100
- Displaying ARP entries 103
- Clearing IP routes 108
- Rate Limiting 111
- VLAN rate limiting 113
- VLAN rate limiting statistics 114
- Configuring OSPF 115
- Enable OSPF on the router 122
- Assign OSPF areas 123
- Assign a totally stubby area 124
- Modify interface defaults 127
- OSPF interface parameters 128
- Assign virtual links 131
- Example 132
- Define redistribution filters 136
- Enable route redistribution 141
- • SI->R3 143
- • SI->R4 143
- • SI->R5 143
- • SI->R6 143
- Modify SPF Timers 146
- • Intra-area routes 147
- • Inter-area routes 147
- • External routes 147
- Modify OSPF traps generated 148
- Modify exit overflow interval 150
- Displaying OSPF information 151
- Syntax: show ip ospf config 152
- • normal 154
- • 1 = point-to-point link 155
- This field Displays 157
- Displaying the data in an LSA 161
- Displaying OSPF trap status 162
- Syntax: show ip ospf trap 163
- Configuring OSPFv3 165
- Enabling OSPFv3 167
- Assigning an NSSA area 168
- • IPv6 static routes 174
- • match metric number 175
- Filtering OSPFv3 routes 177
- • 1 – Type 1 external route 179
- • 2 – Type 2 external route 179
- IPsec for OSPFv3 184
- Configuring IPsec for OSPFv3 185
- IPsec examples 188
- Showing IPsec policy 189
- Showing IPsec statistics 190
- Area configuration of IPsec 192
- Displaying OSPFv3 information 195
- This Field... Displays 196
- • Enabled 201
- • Disabled 201
- Field Description 205
- TABLE 34 OSPFv3 SPF Table 212
- Configuring BGP4 (IPv4) 213
- • IGP is lowest 214
- BGP4 message types 215
- OPEN message 216
- UPDATE message 216
- KEEPALIVE message 217
- NOTIFICATION message 217
- REFRESH message 217
- Implementation of BGP4 218
- BGP4 null0 routing 219
- Configuring BGP4 220
- BGP4 configuration levels 221
- Enabling and disabling BGP4 223
- Disabling BGP4 224
- Multi-Exit Discriminators 226
- Redistributing IBGP routes 227
- Enabling AS4 numbers 228
- AS4 notation 231
- • Logs an error 232
- BGP4 max-as error messages 233
- Originating the default route 235
- Setting the local AS number 239
- Configuring BGP4 neighbors 242
- Encryption example 249
- Enabling next-hop recursion 252
- Redistributing static routes 256
- Changing the device ID 258
- Adding a loopback interface 259
- BGP4 load sharing 259
- Filtering 260
- Defining an AS-path ACL 261
- Using regular expressions 261
- Special characters 262
- Filtering communities 263
- Defining a community ACL 264
- Defining route maps 266
- Matching based on AS-path ACL 269
- Matching based on interface 271
- • ethernet port 272
- • loopback loopback-number 272
- • ve ve-ID 272
- Dynamic route filter update 275
- Filter update delay and BGP 276
- BGP4 policy processing order 277
- Using soft reconfiguration 281
- Clearing traffic counters 287
- Removing route flap dampening 288
- Clearing diagnostic buffers 288
- Configuration steps 289
- Configuration examples 289
- Show commands 290
- Device 1 and 2 291
- Device 6 291
- Displaying BGP4 information 292
- Displaying route details 313
- BGP4 route information 314
- Displaying AS4 details 319
- Attribute entries 320
- AS-path prepend information 321
- Running configuration 321
- Syntax: as-format asdot 322
- Configuring BGP4+ 323
- Adding BGP4+ neighbor 326
- Configuring a route map 326
- Importing routes into BGP4+ 328
- Clearing BGP4+ information 330
- Displaying BGP4+ information 334
- Displaying BGP4+ summary 371
Manuais e produtos relacionados com Acessórios para Computador Brocade Virtual ADX Switch and Router Guide (Supporting AD
Acessórios para Computador Brocade Virtual ADX Security Guide (Supporting ADX v03.1.0 Manual do Utilizador
(180 páginas)
(180 páginas)
Acessórios para Computador Brocade Virtual ADX OpenScript Programmer’s Guide (Support Manual do Utilizador
(30 páginas)
(30 páginas)
Acessórios para Computador Brocade Virtual ADX OpenScript API Guide (Supporting ADX v Manual do Utilizador
(132 páginas)
(132 páginas)
Acessórios para Computador Brocade Virtual ADX Server Load Balancing Guide (Supportin Manual do Utilizador
(408 páginas)
(408 páginas)
Acessórios para Computador Brocade Virtual ADX XML API Programmer’s Guide (Supporting Manual do Utilizador
(878 páginas)
(878 páginas)
Acessórios para Computador Brocade Virtual ADX Licensing Guide (Supporting ADX v03.1. Manual do Utilizador
(20 páginas)
(20 páginas)
Acessórios para Computador Brocade Virtual ADX Installation and Deployment Guide (Sup Manual do Utilizador
(78 páginas)
(78 páginas)
Acessórios para Computador Brocade Virtual ADX Global Server Load Balancing Guide (Su Manual do Utilizador
(198 páginas)
(198 páginas)
Acessórios para Computador Brocade Virtual Connect Enterprise Manager Server Guide (S Manual do Utilizador
(1 páginas)
(1 páginas)
Acessórios para Computador Brocade Virtual ADX Administration Guide (Supporting ADX v Manual do Utilizador
(142 páginas)
(142 páginas)
Acessórios para Computador Brocade Using the Brocade Structured Cabling Components Manual do Utilizador
(16 páginas)
(16 páginas)
Acessórios para Computador Brocade NETAPP – PRODUCT REFERENCE GUIDE Manual do Utilizador
(2 páginas)
(2 páginas)
Pertronix JBA Exhaust 40-3014 manuels
Manuels d'utilisation et guides de l'utilisateur pour Pour la voiture Pertronix JBA Exhaust 40-3014.
Nous fournissons des manuels en pdf 1 Pertronix JBA Exhaust 40-3014 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Comentários a estes Manuais